manualshive.com logo in svg

DEVA Broadcast DB7012, Maintenance And Operation Instruction Manual

Share
Download
DEVA Broadcast DB7012 Maintenance And Operation Instruction Manual Download Page 56

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria

Tel: +359 56 820027, Fax: +359 56 836700

E-mail: [email protected] ,Web: www.devabroadcast.com

- 56 -

REMOTE STATUS REQUEST

The described Feature  is compatible with following DEVA Units:

- 

DB46

 – Compact DAB/DAB+ Monitoring Receiver

- 

DB7012

 – Professional DSP-based DAB/DAB+ Monitoring Receiver

The DEVA Unit can send you a report with the values of the most important parameters at any 

time. Upon receiving your request via SMS, the device’s tuner will be adjusted on the requested 

service number and will make measurement of all the available parameters. Once the procedure 

is completed, an SMS message will be generated and sent to the requestor’s GSM. Command 

Example:

Status 

F

IMPORTANT:

Where 

F

 is service number (preset number set in the device) to Tune. 

Do not include leading zeroes such as “

Status 06

”

The Device will shortly respond back with SMS with the available parameters.

 

Summary of Contents for DB7012
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands