manualshive.com logo in svg

Desmi Modular S-N Series, Operation And Maintenance Instruction, Page: 13 / 20

Share
Download
Desmi Modular S-N Series Operation And Maintenance Instruction Download Page 13

 

DESMI Pumping Technology A/S 

13

 

 

Tagholm 1 

 

9400 Nørresundby 

– Dänemark 

Tlf. nr.: +45 96 32 81 11 
Fax +45 98 17 54 99 
E-mail: desmi@desmi.com 

www.desmi.com

 

 

 

 

 

 

 

13. OPERATING DATA 

The following working pressures are allowed: 
 

Pump 

S32-25-110N 

S50-32-135N 

S70-50-175N 

S70-50-220N 

S70-50-275N 

PRESSUR

E mWC 

45 

45 

65 

100 

150 

Pump 

S80-70-175N 

S80-70-220N 

S80-70-275N 

S100-80-175N  S100-80-220N 

PRESSUR

E mWC 

65 

100 

160 

65 

100 

Pump 

S100-80-275N  S125-80-220N  S125-80-275N  S125-100-220N 

 

PRESSUR

E mWC 

150 

100 

150 

100 

 

 
(10.2 mWC = 1 bar) 
 
The  above-mentioned max.  working  pressure  is 

NOT

  valid  for  pumps  approved by  a  classification 

society.  Pumps  approved  by  classification  societies  have  been  pressure  tested  according  to  the 
requirements of these societies, i.e. a test pressure of 1.5 x the permissible working pressure. The 
test pressure is stated in the test certificate and stamped into the discharge flange of the pump. 
 
The powers stated in the table below are the highest possible absorbed by the pump, whereas the 
min./max. values for flow and pressure indicate DESMI's recommended operating range for the pump 
with the biggest impeller. 
 

Pump 

Max. Power 

kw 

1450/1750/- 

2950/3500 RPM 

Min. Flow 

m3/h 

1450/1750/- 

2950/3500 RPM 

Max. Fflow 

m3/h  

1450/1750/- 

2950/3500 RPM 

Min. Pressure 

mVS 

1450/1750/- 

2950/3500 RPM 

Max. Pressure 

mVS 

 1450/1750/- 

2950/3500 RPM 

S32-25-110N 

0.2/0.3/0.9/1.4 

2.5/3.0/4.5/5.5 

6.0/7.0/12.0/13.5  1.7/2.8/8.0/12.5  3.6/5.3/15.0/21 

S50-32-135N 

0.3/0.5/2.1/3.5 

4,0/4,5/8,0/9,0 

11,0/13,5/23/27  3.0/4.2/12.0/17.0 

6.0/8.7/25/35 

S70-50-175N  0.8/1.2/6.0/10.0 

8.0/10.0/17.5/20 

20/24/45/53 

5.6/8.4/19.0/27 

9.2/13.5/38/53 

S70-50-220N  1.6/2.7/12.3/20.5 

8,0/9,0/15/20 

24/27/45/55 

5.5/9.5/31/40 

14.2/21/63/86 

S70-50-275N 

3.5/6.0/22/35 

10,0/12,0/14,0/16,0 

26/32/32/38 

16.0/21/88/123 

24/34/103/143 

S80-70-175N  1.1/1.8/8.3/13.5 

16,0/17,5/30/35 

39/48/80/95 

4.6/6.0/16.5/23 

8.7/12.5/36/50 

S80-70-220N  2.4/4.2/18.5/31 

15,5/18,5/30/35 

43/53/80/95 

9.5/13.0/42/59 

15.5/22/64/90 

S80-70-275N 

4.4/7.4/32/53 

15,0/18,0/30/35 

40/50/80/95 

16/22/67/94 

25/36/103/143 

S100-80-175N  1.6/2,8/12.5/21 

30/35/60/70 

70/85/150/170 

4.6/6.2/15.0/24 

8.3/12.2/34/48 

S100-80-220N 

3.5/6.1/27/47 

28/37/58/80 

85/97/170/190 

7.0/9.2/31/48 

14,6/21/60/82 

S100-80-275N  6.8/12.0/55/92 

35/40/70/80 

85/100/160/180  13.5/19.5/60/90 

23/33/93/130 

S125-80-220N  4.5/8.0/36.5/61 

60/65/100/120 

135/150/240/250  5.3/10.0/30/54 

12.4/19.0/55/77 

S125-80-275N  8.5/15.0/70/118 

50/60/100/120 

120/145/220/260  14.0/19.8/62/88 

24/34/94/131 

S125-100-

220N 

5.4/9.5/46/74 

70/85/140/140 

170/200/300/320  6.7/10.2/34/54 

12.2/17.8/51/73 

Summary of Contents for Modular S-N Series





















Reviews:

No comments