background image

UNVENTED (VENT-FREE) GAS FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

THERMOSTATICALLY-CONTROLLED MODELS

VSGF28NTE AND VSGF28PTE WITH SPLIT OAK LOGS

®

Shown with optional cabinet mantel, hearth base, and trim accessories.

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

;;;

;;;

;;;

QQQ

QQQ

QQQ

;;;;;;;;;;

;;;;;;;;;;

;;;;;;;;;;

QQQQQQQQQQ

QQQQQQQQQQ

QQQQQQQQQQ

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing
property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other
appliance.

— WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do not use any
phone in your building.

Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire
department.

— Installation and service must be performed by a quali-

fied installer, service agency, or the gas supplier.

Summary of Contents for Vanguard VSGF28NTE

































Reviews: