![background image](http://html1.mh-extra.com/html/desa/cpvsa18r-cpvsa24r/cpvsa18r-cpvsa24r_owners-operation-and-installation-manual_2485847010.webp)
901273-01D
10
For more information, visit www.desatech.com
For more information, visit www.desatech.com
1.
STOP! Read the safety information, above.
2.
Make sure equipment shutoff valve is fully open.
3.
If Using Optional Hand-Held Remote or Wall Switch:
Set switch to OFF position.
WARNING: Burner will come on automatically
within one minute when the selector switch is in the
ON position after the pilot is lit.
4.
Press in and turn control knob clockwise
to the
OFF position.
5.
Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information, above. If you don’t smell
gas, go to the next step.
LIGHTING INSTRUCTIONS
Pilot
Burner
Thermocouple
OPERATING APPLIANCE
For Your Safety Read Before Lighting
Lighting Instructions
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire de-
partment.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don’t try to repair it, call a qualified service techni-
cian or gas supplier. Force or attempted repair may result
in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
OPERATING APPLIANCE
FOR YOUR SAFETY READ
BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
O
F
F
PIL
OT
O
N
Figure 17 - Control Knob and Ignitor Button Location (Shown as
Supplied, No Control Options)
Control
Knob
Ignitor
Button
Figure 18 - Thermopile and Pilot
6.
Press in and turn control knob counterclockwise
to the PILOT position. Press in control knob for five (5)
seconds (see Figure 17).
Note:
You may be running this log set for the first time
after hooking up to gas supply. If so, the control knob may
need to be pressed in for 30 seconds or more. This will al-
low air to bleed from the gas system.
7.
With control knob pressed in, press and release ignitor but-
ton. This will light pilot. Visually locate the pilot on the con-
trol valve cover by the edge of the burner pan to look for flame.
If needed, keep pressing ignitor button until pilot lights.
If the pilot will not stay lit after several tries, turn the gas
control knob to "OFF" and call your service technician or
gas supplier.
8.
Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob.
• If control knob does not pop out when released, contact
a qualified service person or gas supplier for repairs.
Note:
If pilot goes out, repeat steps 4 through 8.
9.
Slightly push in and turn control knob counterclockwise
to the ON position.
10.
If Using Optional Hand-Held Remote or Wall Switch:
Wait one minute and switch selector switch to the ON posi-
tion to light burner.
WARNING: Keep flue open when operating unit.