manualshive.com logo in svg

Deprag AST40-1, Operating Instruction Booklet

Share
Download
Deprag AST40-1 Operating Instruction Booklet Download Page 141

 

141 

17 Accessories 

17.1 Power cord 

Designation 

Product–Code 

Power cable KN-AST10/40-EU 

385443 A 

Power cable KN-AST10/40-US 

385443 B 

Power cable KN-AST10/40-China 

385443 C 

17.2  Emergency Stop Connector 

Plug-in connector to link interface GX9. 

Designation 

Product–Code 

Plug 827507 

17.3  AST40 – PC Connection Cable 

The cable is used to interconnect the AST40 sequence controller with the company 
network or the PC's network interface. This is necessary in order to be able to access the 
sequence controller via the web-based user interface. 

Designation 

Product–Code 

Patch cable 

831902 

17.4 Fieldbus modules 

Only one module can be used per control unit. 
The fieldbus module cannot be used in conjunction with the printer interface. 

17.4.1 Profibus 

Designation 

Product–Code 

Fieldbus AST40 Profibus 

385818 A 

 

17.4.2 Profinet 

Designation 

Product–Code 

Fieldbus AST40 Profinet 

385818 B 

 

17.4.3 EtherCAT 

Designation 

Product–Code 

Fieldbus AST40 Ethercat 

385818 C 

 

17.4.4 EtherNet/IP 

Designation 

Product–Code 

Fieldbus AST40 EthernetIP 

385818 D 

17.5 Printer Interface 

The printer interface cannot be used in conjunction with a fieldbus module. 

Designation 

Product–Code 

AST40 printer interface 

385832 A 

 

Summary of Contents for AST40-1


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands