manualshive.com logo in svg

Deprag AST40-1, Operating Instruction Booklet

Share
Download
Deprag AST40-1 Operating Instruction Booklet Download Page 135

 

135 

15  Error display and troubleshooting 

15.1 System error 

If you discover that the AST40 sequence controller is defective, please send it to 
DEPRAG. Please do not try to troubleshoot or rectify any electrical fault on your own under 
any circumstances whatsoever. 

15.1.1 MINIMAT–EC-Servo Screwdriver 

Number  Meaning 

Trouble shooting 

-- Screwdriver 

not 

found 

Insure that the screwdriver and the connection 
cable are properly attached before you switch on

 

the AST40. 

001 

Temperature too high 

Check the screw assembly process and adjust if 
required. If necessary please contact DEPRAG 
Service. 

002 

Flash not found! 

003 

Error reading Flash file system 
directory! 

004 

Access to protected Flash areas! 

005 

Defective parameter memory! 

006 

File not found! 

007 

Calibration file defective or not initiated!

008 

Resolver signals too small! 

009 

Voltage supply outside of range! 

010 

5V supply outside of range! 

011 

Value outside of limits! 

012 

Incorrect number of available 
measuring systems! 

Troubleshooting not possible 

Table 45: 

System error MINIMAT–EC-Servo screwdriver 

 

15.1.2 Power unit 

Number  Meaning 

Trouble shooting 

-- 

Power unit not found 

Switch the AST40 off and then restart again. If 
the fault remains, please contact the DEPRAG 
Service Department. 

101 

Position indicator index signal not 
found 

102 

QEP position indicator signal missing 
or wrong 

103 

Initialization error, spindle free? 

Ensure that the drive unit of the  
EC-Servo screwdriver turns freely. Re-start 
the AST40. 

104 

Condenser loading error, power unit 
defective 

105 

External Watchdog or overcurrent error

Troubleshooting not possible 

106 

Temperature too high 

Check the screw assembly and adjust it if 
necessary. 
If required, consult the DEPRAG Service 
Department. 

107 Area 

error 

108 Under 

voltage 

... Reserved 

116 Error 

flash 

117 

RAM error or set-up information / 
adjusting values in flash not legible.

 

118 

5V supply error 

119 

3.3V supply error 

Troubleshooting not possible 

Summary of Contents for AST40-1


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands