background image

‡

When the red indicator lights on the charger indicate charging properly, otherwise check if the line is
connected properly.

‡

When the indicator light on the charger changes from red to green, this indicates that the battery is fully
charged.

‡

In this case, please stop charging. Over charging will affect the battery life.

‡

Charging may take up to

- 4 hours. Do not char ge the battery for more than 4 hours. Disconnect the

charger from the balance board and the power supply after 4 hours. Overcharging will reduce the
lifetime of the battery.

‡

The product should not be charged over longer periods.

‡

Never charge the product without supervision.

‡

The product should only be charged in temperatures between 0°C - +45°C.

‡

If charging at lower or higher temperatures, there is a risk that the performance of the battery will be
reduced and a potential risk of damage to the product and personal injury.

‡

Charge and store the product in an open, dry area and away from flammable materials (i.e. materials
that may burst into flames).

‡

Do not charge in sunlight or near open fire.

‡

Do not charge the product immediately after use. Let the product cool down for one hour before
charging.

‡

If the product is left with other persons for example during a holiday period, it should be partially charged
(20-50% charged). Not fully charged.

‡

Do not remove the product from the packaging, charge it fully and then put it back into the packaging.

‡

When shipped from the factory, the product has often been partially charged. Keep the product in a
partially charged state, until it is going to be used.

Chapter 7 The maintenance of the electric scooter

Balance scooter needs to be maintained. This chapter

‡2QO\XVHWKH'&FRQQHFWRUWRFRQQHFWZLWKWKH'&FDEOHIURPWKHFKDUJHUWKDWFRPHVZLWKWKHEDODQFHVFRRWHU
‡'RQRWLQVHUWDQ\IRUHLJQREMHFWVLQWR'&FRQQHFWRU
‡5LVNRIDUFLQJ1HYHUEULGJHWKH'&FKDUJLQJVRFNHWZLWKPHWDOREMHFWV

mainly describes the relevant steps and important

operation reminders to maintain it. Please make sure that the power and charge coil are off before you do
the following operation. You should not operate when the battery is charging.

7.1.

Cleaning

‡

Make sure the power and the charge coil are off.

‡

Wipe the shell of electric scooter with soft

cloth.

‡

Make sure that water and other liquids do not enter the internal parts of the balance scooter as this may
permanently damage the electronics/batteries of the scooter. There is a risk of personal injury.

:$51,1*

:$51,1*

3.5

Summary of Contents for DBO-6501













Reviews: