Initial out-of-box startup:
Select default 8:1 handpiece; TUL-8M (Tulsa Dental Specialties) or
AHP-88MN/MNP (Anthogyr)
.
It is important to select correct handpiece for the system to control
speed and torque accurately. An 8:1 handpiece is required for reciprocation.
Calibration Procedure:
Connect motor and handpiece to system. Secure a file into the hand-
piece. Press & release CAL button. To ensure torque accuracy, calibrate system daily.
WARNING:
During the preprogrammed calibration operation, the file will rotate.
Basic Operation:
Select the Preset Button corresponding to the endodontic rotary file series
you are using. By default, the PROMARK
®
Preset Buttons are set for the file series shown
below. Pressing the Preset Button repeatedly will cycle through the individual files listed below
each series name. The Up/Down Arrow Buttons can also be used to cycle through the files,
and the Right/Left Arrow Buttons can be used to navigate from Preset to Preset.
System Setup:
Enter the System Setup menu by holding down the CAL button until a double
beep is heard. (See Directions For Use for additional setup instructions.)
* Refer to Directions For Use for advanced features
and programming.
Distributed By
DENTSPLY Tulsa Dental Specialties
DENTSPLY International, Inc.
•
608 Rolling Hills Drive • Johnson City, TN 37604
1-800-662-1202 • Fax:1-800-597-2779 • www.TulsaDentalSpecialties.com
Preset Button 1
Default File Series:
DENTSPLY Tulsa Dental Specialties PathFile
®
All Files
File #1: PathFile
®
(All Files)
Preset Button 2
Default File Series:
DENTSPLY Tulsa Dental Specialties WaveOne
®
All Files
File #1: WaveOne
®
(All Files)
An 8:1 handpiece is required for reciprocation.
Preset Button 3
Default File Series:
DENTSPLY Tulsa Dental Specialties ProTaper Next™
File #1: PTN High Torque (All)
File #2: PTN Low Torque (All)
Preset Button 4
Default File Series:
DENTSPLY Tulsa Dental Specialties ProTaper
®
Universal
File #1: ProTaper S1 & SX
File #2: ProTaper S2 & F1
File #3: ProTaper F2, F3, F4, F5
File #4: ProTaper D1 & D2
File #5: ProTaper D3
Preset Button 5
Default File Series:
DENTSPLY Tulsa Dental Specialties VORTEX
®
04, 06 Taper
File #1: VORTEX Orifice (All)
File #1: VORTEX 04, .35 through .50 taper
File #2: VORTEX 04, .25 and .30 taper
File #3: VORTEX 04, .15 and .20 taper
File #4: VORTEX 06, .35 through .50 taper
File #5: VORTEX 06, .25 and .30 taper
File #6: VORTEX 06, .15 and .20 taper
PROMARK
®
Default Preset Chart
Quick Reference Guide
*
Speed
Increase/Decrease
Torque
Increase/Decrease
Motor Direction
Forward/Reverse
Auto-Stop-Reverse/
MAX Torque
Reciprocation
Out Mode
Standby Key
Preset Buttons (5)
Calibration
(single press)
System Setup
(press & hold)
• SETUP OPTIONS:
- Preset Memory Lock
- Recall Factory Setup
• GLOBAL OPTIONS:
- Auto Stop Reverse
- Reverse Beeper
- Torque Warning
- Accessory Warn
- Sleep Mode
- Keypress Beep
- System Volume
- Save Settings
- Cancel
Menu Navigation & Select
Handpiece Ratio Selection
