DentalEZ Aeras Ramvac C11 User Manual Download Page 55

Page: 55 / 77

COMPRESSOR USER MANUAL

866-DTE-INFO
dentalez.com
PN: 7717-004A

PREVENTIVE MAINTENANCE SCHEDULE

This is a recommended schedule for a compressor in a clean, dry environment. Any site other than specified will
decrease maintenance time exponentially.

CHECK FILTER ELEMENT SERVICE INDICATOR

The compressor is equipped with a filter element service indicator. When the indicator turns fully red, the filter element
should be replaced

(FIGURE 44)

NOTE:

Replace element annually, even if the red indicator does not reach the top.

MAINTENANCE (CONTINUED)

Test for Air Leaks

First Week and Annually thereafter

Replace Intake Filter

Annually

Replace Coalescing Filter

Annually or when filter element service indicator moves to completely
red while running

Replace Particulate Filter

Annually or when filter element service indicator moves to completely
red while running

Inspect Dryer

Annually

Test Safety Valve

Annually

Replace Desiccant Cartridges

Every 5 Years

DIFFERENTIAL PRESSURE:

7.25 PSI (0.05 MPA) OR LESS

(THE INDICATOR TIP IS VISIBLE)

DIFFERENTIAL PRESSURE:

14.25 PSI (0.1 MPA) OR MORE

(THE INDICATOR REACHES THE TOP)

FIGURE 44. FILTER WITH ELEMENT SERVICE INDICATOR

SECTION V - CARE

Summary of Contents for Aeras Ramvac C11














































































Search results

Summary of Contents for Aeras Ramvac C11

Reviews:

Brands by name

Popular brands

DentalEZ Aeras Ramvac C11, User Manual

Search results

Summary of Contents for Aeras Ramvac C11

Reviews:

Brands by name

Popular brands