Denon DN-HC5000 - Serato ITCH Hardware/Software Package, Full Manual, Page: 28 / 34

ENGLISH
24
ENGLISH
5 PRESET
• This function is only valid when the “PC” source is selected.
(When the DN-D4000/D4500/BU4500 is connected, the corresponding preset operation is performed.)
• The DN-HC5000 is equipped with a preset function allowing users to store and recall the devices’
operation modes. The function includes the items and values described below.
1. Preset mode
q
Press and hold in the PRESET button for at least 1 second to enter the preset mode.
w
Use the PARAMETERS knob to select the preset item.
e
Select the item and press the PARAMETERS knob to set the preset item to be changed.
r
Next, turn the PARAMETERS knob. The preset data is selected.
t
Select the data and press the PARAMETERS knob to set the preset data to be changed.
y
To make multiple presettings, repeat steps
w
~
t
.
u
The preset mode is turned off when the PRESET button is pressed.
2. Preset items and data
The “*” mark next to the data indicates the default value.
(1) USB Mode Sel: HC5000 ITCH*
Selects the USB communications mode.
(2) CD Model Sel: DN-D4500* / DN-D4000
Select the name of the model to be connected to the DRIVE terminal and controlled.
The BU4500 is the same as the DN-D4500’s drive, so the PRESET setting is “DN-D4500”.
(3) Audio Fs Sel: 44.1k* / 48k / Auto
44.1 kHz: The sampling frequency (Fs) is fixed at 44.1 kHz, regardless of the data sent from the
PC.
48 kHz: The sampling frequency (Fs) is fixed at 48 kHz, regardless of the data sent from the
PC.
AUTO: The sampling frequency (Fs) switches automatically according to the data sent from
the PC.
q
To set “Fs”, press PARAMETERS.
“OK to CHANGE?  ” is displayed on the character display.
w
Press the PARAMETERS knob again.
e
After the sampling frequency is changed, “Audio Fs Sel” is displayed.
(4) Unit No. Set: 1 to 15 / ALL*
Sets the device’s unit number.
For example, when two devices are connected to a PC, set one device to “No. 2” or the like.
(5) CH Set: 1&2* / 3&4 / 5&6
Sets the channel.
(6) JOG Trns Int: 1ms to 20ms (3ms*)
Selects JOG Pulse counts transfer interval.
*For Vista users, please change this setting to 10 ms or higher.
(7) JOG Pulse Sel: 1480* / 740 / 555 / 370 count/cycle
Selects the number of pulses output per one revolution of the jog wheel.
(8) FaderIn Mode: 1-PLAY/CUE / 2-PLAY/CUE*
(9) X-CONT XFD: OFF* / ON
Sets whether to enable or disable X-control input signal cross fader input.
5. Comparison of button operation
q e t y e u i o
w r
Q0 Q1 Q1 Q2 Q4 Q6 Q9
Q3 Q5 Q7 W0 Q8
DN-D4500/BU4500 DN-D4000 DN-HC5000
Function Function Button Name Oparation
q
A1 A1 IN1 Press
q
A2 A2 IN2 Press
q
FLIP/B TRIM FLIP IN3 Press
w
B B
OUT1
OUT2
Press
w
EXIT/RELOOP EXIT/RELOOP OUT3 Press
e
TRACK SELECT(±1) TRACK SELECT(±1)
8 9
Press
TRACK SELECT(±10) TRACK SELECT(±10) SHIFT + Press
r
CUE CUE CUE Press
t
SHUTTLE ring SHUTTLE ring
6 7
Press
y
PLAY/PAUSE PLAY/PAUSE PLAY/PAUSE Press
u
JOG wheel JOG wheel JOG disc Rotate
i
- JOG MODE
JOG MODE
Press
-MP3 SEARCH MODE - Long Press
o
PITCH SLIDER PITCH SLIDER PITCH SLIDER Move
Q0
RELAY - RELAY Press
Q1
•MEMO •MEMO LOAD TO A
LOAD TO B
Press
-PRESET -PRESET Long Press
Q2
Enter Enter x2 Press
Q3
PITCH BEND+/– PITCH BEND+/– PITCH BEND +/– Press
Q4
OPEN/CLOSE OPEN/CLOSE AUTO LOOP Press
Q5
•PITCH/KEY •PITCH
KEY ADJ
Press
-RANGE -RANGE Long Press
Q6
- -FOLDER x1/2 Long Press
Q7
BRAKE -BRAKE CENSOR Press
Q8
- REPEAT AUTO TEMPO Press
Q9
•TIME •TIME
•TIME
Press
-TOTAL -TOTAL Long Press
W0
TITLE •TITLE •TITLE
-CONT./SINGLE
Press
•CONT./SINGLE •CONT./SINGLE Long Press