Denon D-T1 Service Manual Download

Page: 48 / 51

PROCEDURE AFTER REPLACING THE PCB.

PROCEDURE AFTER REPLACING THE U-COM, ETC.

The firmware of U4 (EN25QH16B-104HIP2A) in the MAIN PCB differs depending on the region.

Be sure to follow the instructions in "

FIRMWARE UPDATE PROCEDURE

" to update to the latest firmware

after changing a circuit board.

The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows.

PCB Name Ref. No.

Description

Procedure

after Re-

placement

Remark

MAIN

EN25QH16B-104HIP2A 16Mb

SOFTWARE : DSP

MAIN

U10

STM32F030R8T6

SOFTWARE : Main

Procedure after Replacement

A :

The software has been written. The software is not written at the time of replacement.

B :

The software has been written. The software may need to be rewritten by version updates. Check the

version.

C :

The software has not been written. The software needs to be written after replacement.

See "

FIRMWARE UPDATE PROCEDURE

" for information on writing the software.

D :

The software has been written. Be sure to rewrite with the latest software for your service region.

See "

FIRMWARE UPDATE PROCEDURE

" for information on rewriting the software.

Before Servicing

This Unit

Electrical

Mechanical

Repair Information

Updating

Summary of Contents for D-T1



















































Search results

Summary of Contents for D-T1

Reviews:

Related manuals for D-T1

Brands by name

Popular brands

Denon D-T1, Service Manual

Search results

Summary of Contents for D-T1

Reviews:

Related manuals for D-T1

Brands by name

Popular brands