background image

H

18

Plow Blade Assembly

Dia. 3

Dia. 2

Dia. 4

19

20

7

Tighten these two Hex Nuts

against each other once proper

tension on blade trip pressure is determined.

3/8" Hex Nut (3x)

3/8" Flat Washer (2x)

3/8" Eye Bolt (1x)

Trip Spring (1x)

Dia. 1

Blade not shown for clarity

J

Blade Trip Stop Block

3/8" x 1.25" Hex Bolt

Secure with 3/8" Nylock Nut on Inside

AG

Note Direction

of Blade Bushing

7 OF 9

Step 6 - Assembly of Blade to Push Tube Frame.

Assemble Eye Bolts and eye bolt hardware onto plow blade (See Dia. 1)

1.

Assemble Plow Blade to Push Tube Swivel Bracket with provided hardware shown in (Dia. 2)

2.

Secure trip spring into either of the two hole locations on Push Tube swivel bracket (See Dia. 3)

3.

Tip Blade back towards push tube to secure top ends of Trip Springs into eye bolt.

4.

Once both ends of trip springs are secured, install Trip Blade Stop Block (See Dia. 4)

5.

Apply pressure to back of blade pushing forward to 

1.

extend the trip springs.

Insert Blade Trip Stop Block along with 3/8" x 1.25" Hex Bolt 

2.

thru hole in swivel bracket at this time.

Secure with provided 3/8" Nylock Nut.

3.

Secure trip spring into either of the two hole 

locations on Push Tube swivel bracket

72" Denali Universal Plow System 

Summary of Contents for 810541027509










Reviews: