http://www.delta.com.tw/industrialautomation/
2006-0 7-18
5011617503-2 GE3
TP02G-AS1
Terminal Panels Series
Instruction Sheet
1
WARNING
Please read this manual thoroughly before using the TP02G.
DANGER! DC input power must be OFF before any maintenance. Do not connect or remove wires and
connectors while power up to the circuit. Only qualified technicians are allowed to do the maintenance.
The display panel of the TP02G is waterproof. But please keep away grease, corrosive liquids or sharp
objects from contacting the TP02G.
DANGER! The TP02G requires 24VDC input power. The 24VDC input power should not be connected to
the RS-485 communication port. The unit may be destroyed and can’t be repaired if the input power is
improperly applied. Please confirm the input power wiring is correct before power up.
DANGER! An electrical charge will remain on the DC-link capacitors for 1 minute after power has been
removed. This residual power may be hazardous and the TP02G should not be worked on until this
charge has dissipated. To prevent personal injury, do not conduct any wiring or investigation on the TP02G
until 1 minute after power off. Do not touch any terminals while power is applied to the TP02.
CAUTION! Always ground the TP02G using the grounding terminal. This will not only act as a safety, but
also help filter electrical noise. The grounding method must comply with the laws of the country where the
unit is to be installed.
CAUTION! If you turn the fixed support that is packaged together with TP02G too tight, TP02G may be
damaged.
2
INTRODUCTION
2.1 Model
Explanation
Nameplate
MODEL :
POWER INPUT :
TP02GAS1W6050004
VX.XX
TP02G-AS1
24Vdc 3W
DELTA ELECTRONICS, INC MADE IN XXXXXXX
Production model
Power input spec.
Barcode and
serial number
Version
Note: The words of “MADE IN XXXXX” will be different due to the manufacturing location.
Model Explanation
Serial Number Explanation
TP 02 G
AS 1
-
Reserved
Reserved
T: Text mode
G: Graphic mode
LCD Spec.
Series name
TP02GAS 1 W 6 05 0004
Production serial number
Production weeks
Production year(2006)
Production plant(W:Wuijang)
Version
Production model
2.2 Outline
LCM
Display Area
RS-232 Indication LED
RS-485 Indication LED
Escape/Exit
Alarm Indication LED
Function Keys
Arrow Keys
Enter Key
Back Panel
RS-232
Extension port
5-PIN terminals: Wire gauge: 12-24 AWG / Torque: 4.5 lb.-inch
2.3 Dimensions
Front Panel
Unit: mm[inch]
Right Side Diagram
Unit: mm[inch]
Back side
Vertical View
Unit: mm[inch]
Mounting Panel Dimension
Thickness Range 0.5~9mm
135~136.5[5.31~5.37]
85
[3.35]
Unit: mm[inch]
Installation Method
One easy way is insert TP02G to the opening hole of panel and tight up the screws. However, if a firm mounting
TP02G to the panel is needed, please use the fixed support accessory which is packed together with TP02G, then
infix the fixed support in the back and tight up the screws.
If you turn the screw exceeds torque: 4-5(kg-cm), TP02G may be damaged.
(Note
：
the flat surface should be a Type 4 “Indoor Use Only” enclosure or equivalent.)
Please leave sufficient space (more than 50mm) around the unit for heat dissipation.
Thickness:
0.5~9.0mm
Panel Function Explanation
Panel Component
Explanation
Alarm Indication LED
Status 1: When power is on, the LED will blink slowly for three times.
Status 2: When there is an abnormal situation, the LED will blink quickly along with
an alarm sound.
RS-232 Indication LED
(Yellow)
Will blink when transmitting program and communicating by using RS-232.
RS-485 Indication LED
(Green)
Will blink when communicating by using RS-485.
Esc (Escape/Exit)
Used to cancel an incorrect input, or to Exit a programming step.
Arrow Keys
UP/Pg Up: Used to increase the value or move screen up one page.
Pg Dn/DOWN: Used to decrease the value or move screen down one page.
Left: Left direction key. (move curser to left)
Right: Right direction key. (move cursor to right)
Enter key
Used to input a value or accept a programming instruction.
Function Keys
F0/0: used as a constant 0, or user can define it as function F0.
F1/1: used as a constant 1, or user can define it as function F1.
F2/2: used as a constant 2, or user can define it as function F2.
F3/3: used as a constant 3, or user can define it as function F3.
F4/4: used as a constant 4, or user can define it as function F4.
F5/5: used as a constant 5, or user can define it as function F5.
F6/6: used as a constant 6, or user can define it as function F6.
F7/7: used as a constant 7, or user can define it as function F7.
F8/8: used as a constant 8, or user can define it as function F8.
F9/9: used as a constant 9, or user can define it as function F9.
3
SPECIFICATION
Electrical Specification
Item
TP02G-AS1
Function Key / Digital Key
F0/0~F9/9, ESC, ENTER and ARROW keys
External Input Power
24V (3W Max.)
Memory Capacity
256K Byte
CPU
Hitachi HD64F3064F
RAM of System
32K Byte
Communication Interface
Com1: RS-232 and Com2: RS-485
Waterproof Class of Front Panel
IP65/NEMA4
Environment Condition
0~50
℃
, relative humidity 20-90% RH
（
non-condensing
）
Storage Temperature of Hardware
-20~60
°
C
