Delta M70A 260 Installation And Operation Manual Download Page 141

Page: 141 / 200

141

Installation and Operation Manual for Solar Power Inverter M70A EU V2.0 EN 2020-08-03

10 Maintenance

Replacing the AC surge protection devices

10.10 Replacing the AC surge protection devices

DANGER

Electric shock

Potentially fatal voltages are present in the

inverter during operation. When the inverter

is disconnected from all power sources, this

voltage remains in the inverter for up to 60

seconds.

►

Perform the instructions listed in “10.4 Mak-

ing preparations for maintenance work - dis-

connecting the inverter from the grid (AC)

and solar modules (DC)”, page 115

before

you start work on the inverter!

Type 2 AC surge protection devices are installed

as standard. Type 1+2 combined AC surge pro-

tection devices can be ordered as accessories.

∫

The screws are very small and can easily fall

down. You should therefore use a magnetic

screwdriver.

1. Unscrew and remove the cover of the type 2 AC surge

protection devices.

Summary of Contents for M70A 260









































































































































































































Search results

Summary of Contents for M70A 260

Reviews:

Related manuals for M70A 260

Brands by name

Popular brands

Delta M70A 260, Installation And Operation Manual

Search results

Summary of Contents for M70A 260

Reviews:

Related manuals for M70A 260

Brands by name

Popular brands