Delta DVS-328 series User Manual Download Page 94 | Manualshive

Page: 94 / 246

background image

C h a p t e r 3 F e a t u r e d F u n c t i o n s

3 - 7 3

Multicast MAC Address Configuration

Description

Factory default

VLAN ID

Specify the VLAN ID.

None

MAC Address

Specify the multicast MAC address.

None

Member Ports

Select the member port or LAGs for this multicast group.

None

Static Multicast MAC Address Table

Item

Description

VLAN ID

The field displays the identifier of VLAN.

MAC Address

The field displays the multicast MAC address.

Member Ports

The field displays the multicast member ports.

Status

The field displays the status of the multicast MAC address.

3.5.5

GMRP Configuration

The GARP (Generic Attribute Registration Protocol) Multicast Registration Protocol helps control the flooding of
multicast packets. The GMRP-enabled switches dynamically register and de-register group membership
information with the MAC networking devices attached to the same segment.

Note:

If you need to configure the GMRP Port Configuration, we suggest that you make sure that GMRP
Configuration is enabled, or the function can not be actived on Port Configuration.

«
...
92
93
94
95
96
...
»

Summary of Contents for DVS-328 series























































































































































































































































Reviews:

No comments

Related manuals for DVS-328 series

Brand: i-MO Pages: 58

FrameSaver 9120

Brand: Paradyne Pages: 2

TotalStorage SAN16M-R SAN

Brand: IBM Pages: 116

SteelCentral NetExpress

Brand: Riverbed Pages: 38

Brand: NetComm Pages: 69

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

PD-9501-10GCO/AC

Brand: Microchip Technology Pages: 41

Wireless Kit 108MBPS

Brand: Topcom Pages: 100

Brand: StarTech.com Pages: 16

ControlCenter-IP 2.0

Brand: G&D Pages: 60

Brand: Hama Pages: 45

Brand: Belkin Pages: 2

Brand: Patton electronics Pages: 93

Brand: Tenda Pages: 74

Brand: Alcatel-Lucent Pages: 612

Brand: Addi-Data Pages: 20

Brand: Ekselans Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands