background image

19

Fig. 46

Fig. 48

7.

IMPORTA N T:For ease in rotating the cutterhead

during the knife setting operation, pull outward on latch

(H) Fig. 46, and open hinged access door (J). This pro-

vides access to the cutterhead pulley (K) Fig. 47, and

belt (L) allowing you to rotate the cutterhead. CAUTION:

After knives are adjusted, make certain the access door

(J) is in the closed and locked position.

8.

Replace the knife locking bars, lifter springs and

knives into each slot in the cutterhead. W ARNING: C A R E

M U S T B E TA K E N W H E N INSERTING T H E KNIVES

A S T H E CUTTING E D G E S A R E V E RY S H A R P.  Push

the knives down as far as possible and snug up the knife

locking screws by turning them counterclockwise just

enough to hold the knives in position.

9.

Construct a  U  shaped block out of hardwood simi-

lar to the one shown at (M) Fig. 48, and place this block

on the rear table over the cutterhead, as shown. Using

wrench (C), loosen knife locking screws by turning them

clockwise. The knife (O) will lift up and contact the ends

of the gage block (M). The knives are adjusted correctly

when the cutting edge of the knife contacts the gage

block when the knife is at its highest point. When you are

certain the knife is adjusted properly, tighten the knife

locking screws by turning them counterclockwise.

10. Adjust the remaining two knives in the same manner.

W ARNING: M A K E C E R TAIN T H AT A L L KNIVES A R E

S E C U R E LY FA S T E N E D IN C U T T E R H E A D B E F O R E

TURNING O N P O W E R.

11. Replace cutterhead guard.

M

O

C

J

H

Fig. 47

K

L

Summary of Contents for 37-360





















Reviews: