background image

17

Fig. 43

BEVELING

To cut a bevel, lock the fence at the required angle and

run the work across the knives while keeping the work

firmly against the fence and tables. Several passes may

be necessary to arrive at the desired result. When the

angle is small, there is little difference whether the fence

is tilted to the right or left. However, at greater angles

approaching 45 degrees, it is increasingly difficult to hold

the work properly when the fence is tilted to the right. The

advantage of the double-tilting fence is appreciated

under such conditions.

When tilted to the left, the fence forms a V-shape with the

tables, and the work is easily pressed into the pocket

while passing it across the knives. If the bevel is laid out

on the piece in such direction that this involves cutting

against the grain, it will be better to tilt the fence to the

right.

Fig. 43, illustrates a slight bevel being cut onto the edge

of a workpiece.

TAPER CUTS

One of the most useful jointer operations is cutting an edge to a taper.

 The method can be used on a wide variety of

work. Tapered legs of furniture are a common example.

Instead of laying the piece on the infeed table, lower the forward end of the work onto the outfeed table. Do this very

carefully, as the piece will span the knives, and they will take a  bite  from the work with a tendency to kick back unless

the piece is firmly held. Now push the work forward as in ordinary jointing. The effect is to plane off all the stock in front

of the knives, to increasing depth, leaving a tapered surface.

The ridge left by the knives when starting the taper may be removed by taking a very light cut according to the regular

method for jointing, with the infeed table raised to its usual position.

Practice is required in this operation, and the beginner is advised to make trial cuts on waste material. Taper cuts over

part of the length and a number of other special operations can easily be done by the experienced craftsman.

CUTTING A R A B B E T

IMPORTA N T:D O N O T R E M O V E T H E C U T T E R H E A D

G U A R D W H E N P E R F O R M I N G R A B B E T I N G O P E R A-

TIONS.

Rabbeting is similar to a jointing operation except that

only a partial cut is made in the edge of the work surface,

as shown in Fig. 44.

Make certain the machine is disconnected from the

power source when adjusting the fence for rabbeting!

Adjust the fence to the desired width of the rabbet cut.

W A R N I N G:T H E U N C U T PORTION O F T H E R A B B E T

C A N N O T B E G R E AT E R THAN 3/4 .

Hold the work firmly against the fence while making the

rabbet cut. NOTE: D O N O T M A K E C U T S G R E AT E R

T H A N 1/8

IN E A C H PASS. IF A D E E P E R C U T IS RE-

QUIRED, MAKE S E V E R A L C U T S TO A M A X I M U M O F

3/8

F O R THIS JOINTER.

Fig. 44

Summary of Contents for 37-285
























Reviews: