Delta-T RZ-05A Series User'S & Technical Manual Download Page 17 | Manualshive

Page: 17 / 26

background image

4421 Tradition Trail ● Plano, Texas 75093 ● 972-964-2700 ● 800-836-7472

URL:

www.iscenclosurecooling.com

● Email:

[email protected]

SP-ENG-210-100-07 Rev 2.2

17

|

P a g e

Field Serviceable Parts

ISC carefully designs and selects components with the maximum life expectancy. Due to OEM
manufacturing tolerances, poor unit maintenance or extreme operating conditions, components may
fail before their maximum life expectancy. The table below lists parts that are serviceable in the field by
an Air Conditioner Technician.

Part Description

ISC Part #

Digital Controller

52110-1 for 120VAC
52112-1 for 230VAC/480VAC
52111-1 for 120VAC w/ both Dry C and Heater
52111-2 for 230VAC/480VAC w/ both Dry C and Heater

Low Pressure Switch

38151-1

Condenser Fan Cut-In Pressure Switch

38001-1

Temperature Probe

52126-1

Condenser Fan Relay

55761-1 for 120VAC
55762-1 for 230VAC/480VAC

Thermal Expansion Value TXV

NE050/060 = 32002-1, NE080 = 32003-1

Compressor

NE050 = 31530-1 for 120VAC, 31011-1 for 230VAC/480VAC
NE060 = 31020-1 for 120VAC, 31011-1 for 230VAC/480VAC
NE080 = 31020-1 for 120VAC, 31025-1 for 230VAC/480VAC

Compressor Thermal Overload

NE050 = 31530-2 for 120VAC, 31011-2 for 230VAC/480VAC
NE060 = 31020-2 for 120VAC, 31011-2 for 230VAC/480VAC
NE080 = 31020-2 for 120VAC, 31025-2 for 230VAC/480VAC

Gasket Installation Kit

71403-N568

Evaporator Fan

NE050 = 41005-1-1 for 120VAC, 41005-2-1 for 230VAC/480VAC
NE060/080 = 41037-1-1 120VAC, 41037-2-1 for 230VAC/480VAC

Condenser Fan

NE050 = 41055-1-1 for 120VAC, 41055-2-1 for 230VAC/480VAC
NE060/080 = 41045-1-1 120VAC, 41045-2-1 for 230VAC/480VAC

Filter Media

44011-1 (Available in packs of 12: Part # 44203)

Capacitor

NE050 = 54001-1 for 120VAC/230VAC/480VAC
NE060/080 = 54004-1 for 120VAC, 54001-1 for 230VAC/480VAC

Safety Information

Unit is carefully designed to restrict access to movable parts to minimize any potential injury. This Air
Conditioner has been tested by UL to meet the safety requirements of the UL484 specification. When
working with the DELTA-T Air Conditioner always makes sure shroud is installed. Verify proper
voltage is applied to unit as specified in the UL label of the Air Conditioner. In the event of a field
service repair, power down unit using the power on/off switch and disconnect power from unit. It is
always recommended to use a licensed Air Conditioner Technician for internal diagnostics and repairs
issues.

Contact ISC technical support for further details on opening the unit and troubleshooting tips.

«
...
15
16
17
18
19
...
»

Summary of Contents for RZ-05A Series



























Reviews:

No comments

Related manuals for RZ-05A Series

Brand: AiroDoctor Pages: 8

MOB30-18HDN1-MQ0W

Brand: ZenAire Pages: 94

Brand: inventum Pages: 100

Air Boss T1001 Module

Brand: Trion Pages: 23

VERT-I-PAK B-SERIES

Brand: Friedrich Pages: 20

Brand: Daikin Pages: 178

Brand: American Comfort Pages: 15

Brand: Seifert Pages: 23

Brand: Vremi Pages: 9

Brand: Aktobis Pages: 12

Brand: Pfannenberg Pages: 37

Brand: Olmo Pages: 19

Brand: Movincool Pages: 50

Brand: Ravanson Pages: 67

Brand: Akai Pages: 25

Brand: Midea Pages: 9

Brand: Teesa Pages: 44

Brand: Kelvinator Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands