Warning
Please read this instruction sheet carefully before use.
DVPAETB series is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust,
humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the
device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may
occur.
DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur.. Check
all the wiring again before switching on the power, and DO NOT touch any terminal when the power is switched
on.
Introduction
DVPAETB-ID32A/OR16A extension drive board is designed for connecting to DVP32SM11N and
DVP32SN11TN, the I/O module with multiple points.
Product Profile & Outline
DVPAETB-ID32A
Unit: mm
1. 40-pin header connector
4. Bottom fastening lock
2. 36-pin input terminal
5. 40-pin IDC connection cable*1
3. DIN rail clip
6. DIN rail
*1: You can select Delta’s standard accessory DVPACAB7A10 (IDC 40P-40P 1m)
DVPAETB-OR16A
Unit: mm
ENGLISH
1. 2-PIN power input terminal
7. DIN rail clip
2. Power indicator
8. Bottom fastening lock
3. 20-pin header connector
9. 20-pin IDC connection cable*2
4. Output indicator
10. DIN rail
5. Output relay
11. Output point action indicator
6. 9-pin+11-pin output terminal
*2: You can select Delta standard accessory DVPACAB7B10 (IDC 40P-20Px2 1m)
Model Explanation
Input Unit
Output Unit
Model Name
Power
Points
Type
Points
Type
DVPAETB-ID32A
N/A
32
DC Type
Sink/Source
0
N/A
DVPAETB-OR16A
24V DC
0
N/A
16
Relay 250V AC/30V DC
2A/1 point, 5A/COM.
Connection Cable
Model Name
Length
Pins
Connector
Applicable PLC (accessory)
DVPACAB7A10
1m
40P-40P
IDC connector on
both sides
DVP32SM11N (DVPAETB-ID32A)
DVPACAB7B10
1m
40P-20Px2
IDC connector on
both sides
DVP32SN11TN (DVPAETB-OR16A)
Specifications
Electrical Specifications
Model
Item
DVPAETB-ID32A
DVPAETB-OR16A
Insulation resistance
> 5M
Ω
(all I/O point-to-ground: 500V DC)
Operation/storage
environment
Operation: 0 ~ 55°C (temperature), 50 ~ 95% (humidity), pollution degree 2
Storage: -25 ~ 70°C (temperature), 5 ~ 95% (humidity)
Weight (g)
166g
216g
Input Point
Type
DC (There is no actual input device. Please refer to spec. of DVP32SM11N.)
Input format
DC (SINK or SOURCE)
Input voltage/current
24V DC 5mA
Off
→
On more than 16V DC
Action level
On
→
Off less than 14.4V DC
Response time
Approx. 10ms
Circuit isolation/operation
instruction
By internal photocoupler / LED indicators
Output Point
Type
Relay-R
Current specification
2A/1point (5A/COM)
Voltage specification
< 250V AC, 30V DC
75VA (inductive)
Maximum load
90W (resistive)
Response time
Approx. 10ms
Installation & Wiring
Terminals of Digital I/O Extension Unit
ID32A
X0 X2 X4 X6 X10 X12 X14 X16 X20 X22 X24 X26 X30 X32 X34 X36
X1 X3 X5 X7 X11 X13 X15 X17 X21 X23 X25 X27 X31 X33 X35 X37
S/S S/S
S/S S/S
OR16A
Y1 Y2 Y3 C1 Y4 Y5 Y6 Y7 C2 Y10 Y11 Y12 Y13 C3 Y14 Y15
C0 Y0
Y14 Y15
+24V
GND
Y1 Y2 Y3
Y4 Y5 Y6 Y7
Y10 Y11 Y12 Y13
Y14 Y15
Y0
Y14 Y15
Installation
How to install DIN rail:
Fix one side first.
Next, insert the drive board into the DIN rail and
check if the board is tightly knitted to the rail.
To uninstall the board, push up the board and pull it
out. Follow the steps as indicated in the figure.
Configuration of output points in the connection of DVP32SN11TN and DVPAETB-OR16A:
Environment Notice:
DO NOT
install the board in the environment with dust, smoke, metallic debris, corrosive or
flammable gas
DO NO
install the board in the premise of high temperature, humidity, direct shock and vibration
DO NOT
place the I/O signal wires and power supply wires in the same wiring duct or use cables
of multiple cores.
Wiring of I/O Points
Wiring of input points:
There are two types of DC inputs, SINK and SOURCE.
Wiring Loop
DC
(DC Signal IN)
SINK Mode
S/S
X37
X36
X35
X0
+24V GND
POWER SUPPLY
SINK Mode
DVPAETB-ID32A
Wiring Loop
DC
(DC Signal IN)
SOURCE Mode
S/S
X37
X36
X35
X0
+24V GND
POWER SUPPLY
SOURCE Mode
DVPAETB-ID32A
Wiring of output points:
Relay output circuit wiring
MC2
MC1
9
10
C0
Y0
Y4
Y2
C2
Y3
Y5
Y1
5
2
3
7
8
1
6
7
2
5
4
MC2
MC1
Y6
Y7
8
DVPAETB-OR16A
1. Other output points
6. Varistor*3
2. Fuse
7. Inductive load
3. Reverse current protection diode*1
8. Incandescent light (resistive load)
4. Manual exclusive output*2
9. DC power supply
5. Emergency stop: Uses external switch
10. AC power supply
*1: There is no intermal protection circuit inside the output relay of DVPAETB-OR16A. Therefore, when
activating a DC inductive load, please parallelly connect it to a reverse current protection diode to extend
the life of the contact. The reverse current protection diode shall comply with the following specifications:
a. Able to endure maximum 5 ~ 10 times the amount of the load voltage.
b. Its forward current has to be bigger than the load current.
*2: The manual exclusive output uses external circuit and forms an interlock, together with the program
inside the PLC, to ensure safety protection in case of any unexpected errors.
*3: There is no internal protection circuit inside the output relay of DVPAETB-OR16A. Therefore, when
activating an AC inductive load, please parallelly connect it to a varistor (0.1uF + “100ohm to 120ohm”) to
reduce the interference in the AC load and extend the life of the contact.
Note:
Please select proper safety wires. If the wires are not sufficient in long-time operation, overheating and
sparking may occur.
注意事項
請在使用之前，詳細閱讀本使用說明書。
本機為開放型
(OPEN TYPE)
機殼，因此使用者使用本機時，必須將之安裝於具防塵、防潮及免於電擊
/
衝
擊意外之外殼配線箱內。另必須具備保護措施（如：特殊之工具或鑰匙才可打開）防止非維護人員操作或
意外衝擊本體，造成危險及損壞。
交流輸入電源不可連接於直流類型之輸入
/
出信號端，否則可能造成嚴重的損壞，因此請在上電之前再次確
認電源配線。請勿在上電時觸摸任何端子。
產品簡介
DVPAETB-ID32A/OR16A
擴充驅動板，主要用於與高密度
I/O
模組
DVP32SM11N
及
DVP32SN11TN
連接使用。
產品外觀及各部介紹
DVPAETB-ID32A
單位：
mm
1. 40PIN
牛角座
4.
底座固定鎖
2. 36PIN
輸入端子
5. 40PIN IDC
連接線
*1
3. DIN
軌固定槽
6. DIN
軌
*1:
可使用台達標準配件
DVPACAB7A10 (IDC 40P-40P 1m)
DVPAETB-OR16A
單位：
mm
繁體中文
1. 2PIN
電源輸入端子
7. DIN
軌固定槽
2.
電源指示燈
8.
底座固定鎖
3. 20PIN
牛角座
9. 20PIN IDC
連接線
*2
4.
輸出指示燈
10. DIN
軌
5.
輸出繼電器
11.
輸出點動作指示燈
6. 9PIN+11PIN
輸出端子座
*2:
可使用台達標準配件
DVPACAB7B10 (IDC 40P-20Px2 1m)
配件型號
輸入單元
輸出單元
配件名稱
電源
點數
形式
點數
形式
DVPAETB-ID32A
N/A
32
DC Type
Sink/Source
0
無
DVPAETB-OR16A
24V DC
0
無
16
繼電器
Relay 250V AC/30V DC
2A/1
點，
5A/COM
。
連接線型號
線材名稱
線長
PIN
數
線材接頭種類
適用機種（配件）
DVPACAB7A10
1m
40P-40P
二側
IDC
接頭
DVP32SM11N (DVPAETB-ID32A)
DVPACAB7B10
1m
40P-20Px2
二側
IDC
接頭
DVP32SN11TN (DVPAETB-OR16A)
規格
電氣規格
機
種
項
目
DVPAETB-ID32A
DVPAETB-OR16A
絕緣阻抗
5 M
Ω
以上（所有輸出／入點對地之間
500V DC
）
操作／儲存環境
操作：
0 ~ 55°C
（溫度），
50 ~ 95%
（濕度），
污染等級
2
儲存：
-25 ~ 70°C
（溫度），
5 ~ 95%
（濕度）
重量（約）
(g)
166g
216g
輸入點規格
輸入點形式
直流（無實際輸入元件，以下輸入規格參考於
DVP32SM11N
。）
輸入形式
直流（
SINK
或
SOURCE
）
輸入電壓電流
24V DC 5mA
Off
→
On 16V DC
以上
動作位準
On
→
Off 14.4V DC
以下
反應時間
約
10ms
電路隔離
/
操作指示
內部之光耦合器
/
內部之
LED
顯示燈
