DeLonghi EUROCHEF - PRO Installation Instructions Manual Download

Page: 1 / 16

Air-2

EUROCHEF - PRO WALL HOOD

INSTALLATION INSTRUCTIONS

Shown with accessory Duct Cover Kit and accessory Warming Lamp Kit

APPROVED FOR ALL RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT:

Save these Instructions for the Local Electrical Inspector’s use.

INSTALLER:

Leave these Instructions with this unit for the owner.

OWNER:

Retain these instructions for future reference.

SAFETY WARNING

Turn off power circuit at service panel and lock out panel

before wiring this appliance.

REQUIREMENT: 120VAC, 60 Hz. 20A Branch Circuit

READ AND SAVE THESE INSTRUCTIONS

TIMER

EUROCHEF - PRO WALL HOOD

EUROCHEF U.S.A.

41 MERCEDES WAY SUITE 25 EDGEWOOD NEW YORK 11717 – TEL. 866-844-6566

WWW.DELONGHIMAJORAPPLIANCES.COM

WWW.DELONGHI RANGES.COM

Summary of Contents for EUROCHEF - PRO

















Search results

Summary of Contents for EUROCHEF - PRO

Reviews:

Related manuals for EUROCHEF - PRO

Brands by name

Popular brands

DeLonghi EUROCHEF - PRO, Installation Instructions Manual

Search results

Summary of Contents for EUROCHEF - PRO

Reviews:

Related manuals for EUROCHEF - PRO

Brands by name

Popular brands