background image

Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your

building.

• lmmediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

• lf you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer,
service agency, or the gas supplier.

WARNING:

IF THE INFORMATION IN THIS MANUAL IS NOT

FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

IMPORTANT - PLEASE READ AND FOLLOW

Before beginning, please read these instructions completely and carefully.

Do not remove permanently affixed labels, warnings, or plates from the product. This
may void the warranty.

Please observe all local and national codes and ordinances.

Please ensure that this product is properly grounded.

The installer should leave these instructions with the consumer who should retain
for local inspector's use and for future reference.

The electrical plug should always be accessible

Installation must conform with local codes or in the absence of codes, the National Fuel
Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance with the
National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN CANADA:
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas
Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.
Electrical installation must be in accordance with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.

Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual
gas shut-off valve must be installed in the gas supply line ahead of the appliance in the gas
stream for safety and ease of service.

B U I L T - I N

G A S

C O O K T O P

with safety valve device

• USERS OPERATING INSTRUCTIONS
• INSTALLATION ADVICE

Model  

DEGCT424F..

Summary of Contents for DEGCT424 Series





















Reviews: