Dell XPS 8930 Service Manual Download Page 84

Page: 84 / 142

Removing blower and heat-sink

assembly

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before

working inside your computer

. After working inside your computer, follow

the instructions in

After working inside your computer

. For more safety best

practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

WARNING: The heat sink may become hot during normal operation. Allow
sufficient time for the heat sink to cool before you touch it.

CAUTION: For maximum cooling of the processor, do not touch the heat
transfer areas on the heat sink. The oils in your skin can reduce the heat
transfer capability of the thermal grease.

Prerequisites

Remove the

right-side cover

Follow the procedure from step 1 to step 2 in “

Removing the power-supply unit

”.

Procedure

Remove the screws that secure the blower to the heat-sink assembly.

Summary of Contents for XPS 8930















































































































































Search results

Summary of Contents for XPS 8930

Reviews:

Related manuals for XPS 8930

Brands by name

Popular brands

Dell XPS 8930, Service Manual

Search results

Summary of Contents for XPS 8930

Reviews:

Related manuals for XPS 8930

Brands by name

Popular brands