Dell XPS 8930 Service Manual Download Page 108

Page: 108 / 142

Replacing the wireless card

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before

working inside your computer

. After working inside your computer, follow

the instructions in

After working inside your computer

. For more safety best

practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Procedure

CAUTION: To avoid damaging the wireless card, do not place any cables
under it.

Align the notch on the wireless card with the tab on the wireless-card slot.

Slide the wireless card at an angle into the wireless-card slot.

Connect the antenna cables to the wireless card.
The following table provides the antenna-cable color scheme for the wireless
card supported by your computer.

Table 3. Antenna-cable color scheme

Connectors on the wireless card

Antenna-cable color

Main (white triangle)

White

Auxiliary (black triangle)

Black

Align the screw hole on the wireless-card bracket with the screw hole on the
wireless card and the system board.

108

Summary of Contents for XPS 8930















































































































































Search results

Summary of Contents for XPS 8930

Reviews:

Related manuals for XPS 8930

Brands by name

Popular brands

Dell XPS 8930, Service Manual

Search results

Summary of Contents for XPS 8930

Reviews:

Related manuals for XPS 8930

Brands by name

Popular brands