Dell XPS 8920 Service Manual Download

Page: 39 / 102

Replacing the solid-state drive

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

CAUTION:

Solid-state drives are fragile. Exercise care when handling the solid-state drive.

Procedure

1. Align the notch on the solid-state drive with the tab on the solid-state drive slot.
2. Insert the solid-state drive at a 45-degree angle into the solid-drive drive slot.

For more information, see “

System-board components

”.

3. Replace the screw that secures the solid-state drive to the system board.

Figure 18. Replacing the solid-state drive

1. tab

2. notch

3. solid-state drive slot

4. solid-state drive

5. system board

6. M2 X 2.5 screw

Replacing the solid-state drive

Summary of Contents for XPS 8920







































































































Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands

Dell XPS 8920, Service Manual

Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands