Dell XPS 8920 Service Manual Download

Page: 37 / 102

Removing the solid-state drive

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

CAUTION:

Solid-state drives are fragile. Exercise care when handling the solid-state drive.

CAUTION:

To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.

Prerequisites

1. Remove the

right-side cover

2. Remove the

full-length graphics card

(if installed).

Procedure

1. Remove the screw that secures the solid-state drive to the system board.
2. Slide and lift the solid-state drive off the system board.

For more information, see “

System-board components

”.

Figure 17. Removing the solid-state drive

1. solid-state drive

2. solid-state drive slot

Removing the solid-state drive

Summary of Contents for XPS 8920







































































































Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands

Dell XPS 8920, Service Manual

Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands