Dell XPS 8920 Service Manual Download | Manualshive

Page: 33 / 102

background image

Replacing the primary hard-drive

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

CAUTION:

Hard drives are fragile. Exercise care when handling the hard drive.

Procedure

1. Place the hard drive into the hard-drive cage.
2. Align the screw holes on the hard-drive cage with the screw holes on the hard drive.
3. Replace the screws that secure the hard drive to the hard-drive cage.
4. Insert the hard-drive cage into the chassis.
5. Replace the screws that secure the hard-drive cage to the chassis.
6. Connect the data and power cables to the hard drive.

Post-requisites

right-side cover

.

17

Replacing the primary hard-drive

33

«
...
31
32
33
34
35
...
»

Summary of Contents for XPS 8920







































































































Reviews:

No comments

Related manuals for XPS 8920

System x3200 M3

Brand: IBM Pages: 42

Brand: MicroTouch Pages: 52

Brand: eMachines Pages: 406

Brand: Kontron Embedded Computers Pages: 48

Vaio VGN-CR515E

Brand: Sony Pages: 2

VAIO VGN-C270CNH

Brand: Sony Pages: 2

VAIO VGN-BZ570N02

Brand: Sony Pages: 3

VAIO VGN-BZ570N01

Brand: Sony Pages: 3

Vaio VGN-AW11M/H

Brand: Sony Pages: 40

VAIO VGN-CS Series

Brand: Sony Pages: 175

VAIO VGN-C270CNH

Brand: Sony Pages: 179

Brand: Sony Pages: 197

Vaio VGN-CR Series

Brand: Sony Pages: 200

VAIO VGN-BZ570N01

Brand: Sony Pages: 218

VAIO VGN-BX396XP

Brand: Sony Pages: 228

Brand: Monit Rally Pages: 2

Brand: Canon Pages: 186

Stockholm Corner Desk

Brand: FRISKA Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands