Dell XPS 8920 Service Manual Download

Page: 28 / 102

Removing the primary hard-drive

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

CAUTION:

Hard drives are fragile. Exercise care when handling the hard drive.

CAUTION:

To avoid data loss, do not remove the hard drive while the computer is in sleep or on state.

Prerequisites

Remove the

right-side cover

Procedure (with tabs)

1. Disconnect the data and power cables from the hard-drive.
2. Press the release tabs on the hard-drive carrier and slide the hard-drive carrier out of the hard-drive cage.

Figure 12. Removing the hard-drive assembly

1. data cable

2. power cable

3. hard-drive cage

4. release tabs

Removing the primary hard-drive

Summary of Contents for XPS 8920







































































































Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands

Dell XPS 8920, Service Manual

Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands