Dell Vostro 3401 Service Manual Download Page 48 | Manualshive

Page: 48 / 87

background image

About this task

Steps

1. Reconnect the power button FFC and IO daughter board FFC to the IO daughter board.
2. Place the IO daughter board onto the from the system.
3. Replace the four (M2x4) screws to secure the IO daughter board to the palmrest.
4. [For models shipped without a fingerprint reader] : Reconnect the power button FFC, IO daughter board FFC, and display

cable to the connectors on the system board.

5. [For models shipped with a fingerprint reader] : Reconnect the fingerprint reader to IO daughter FFC and IO daughter board

to system board FFC from the IO daughter board.

Next steps

1. Connect the

.

2. Install the

.

3. Install the

.

4. Follow the procedure in

after working inside your computer

.

Touchpad

Removing the touch pad assembly

Prerequisites

1. Follow the procedure in

before working inside your computer

.

48

Disassembly and reassembly

«
...
46
47
48
49
50
...
»

Summary of Contents for Vostro 3401
























































































Reviews:

No comments

Related manuals for Vostro 3401

Brand: Hypertec Pages: 1

Brand: Medion Pages: 90

Brand: Conrad Electronic Pages: 3

TravelMate 4150

Brand: Acer Pages: 127

Brand: Epson Pages: 11

Brand: Brother Pages: 258

Brand: HP Pages: 17

Brand: HP Pages: 4

Brand: HP Pages: 6

Brand: HP Pages: 46

Brand: HP Pages: 70

Brand: HP Pages: 136

Brand: HP Pages: 138

Pavilion TouchSmart 11-e000

Brand: HP Pages: 85

Brand: HP Pages: 34

Pavilion TouchSmart 11-e000

Brand: HP Pages: 87

Pavilion Sleekbook 14-b000

Brand: HP Pages: 85

Brand: HP Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands