manualshive.com logo in svg

Dell USC, User Manual

Share
Download
Dell USC User Manual Download Page 99

USC and USC-LCE Operations

99

4

System powers off and perform iDRAC configuration and firmware 

restore. After completion, iDRAC resets and takes up to 10 minutes before 

the system powers on.

5

System powers on and restore process is complete. Check the Lifecycle 

logs for the restore process entries.

See Also

Import Server Profile

Importing Server Profile after Motherboard 

Replacement

Prerequisites

• A backup of the server with the old motherboard.
• If you are restoring from a the Dell vFlash SD card, it must be installed 

and must contain the backup image in a folder labeled SRVCNF. This 

image must be from the same platform that you are trying to restore.

• If you are restoring from a network share, make sure that the network share 

where the backup image file is stored is still accessible.

Workflow

After replacing the motherboard, follow the steps under 

vFlash SD Card

, 

Network Share

, or 

USB Device

 to restore the system information.

Post-requisites

• See 

Post-import Scenario

• The Service tag is restored from the backup file on the new motherboard.

Summary of Contents for USC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands