manualshive.com logo in svg

Dell USC, User Manual

Share
Download
Dell USC User Manual Download Page 93

USC and USC-LCE Operations

93

Supported Devices

You can update the part firmware and configuration for the following devices:

 

NOTE: 

Only part firmware updates are supported on SAS cards and power supply 

units.

• NICs  (Broadcom)
• PERC, SAS, and CERC series 6 and 7
• Power  Supply  Units

Collect System Inventory on Restart

When you enable the 

Collect System Inventory On Restart

 property, 

hardware inventory and part configuration information is discovered and 

compared with previous system inventory information on every system 

restart. To do this:

1

In the left pane, click 

Platform Restore

.

2

Click 

Part Replacement Configuration

.

3

Click either 

Enabled

 or 

Disabled

 from the 

Collect System Inventory on 

Restart

 drop-down.

Part Firmware Update

From the part firmware update drop-down, select one of the following:

•

Disabled

 — Firmware update on replaced parts is not performed. 

•

Allow version upgrade only

 — Firmware update on replaced parts is only 

performed if the firmware version of the new part is lower than the existing 

part.

•

Match firmware of replaced part

 — Firmware on the new part is updated 

to the version of the original part.

Summary of Contents for USC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands