manualshive.com logo in svg

Dell USC, User Manual

Share
Download
Dell USC User Manual Download Page 88

88

USC and USC-LCE Operations

If the installation is successful, you are able to boot to Unified Server 

Configurator — Lifecycle Controller Enabled.

If the installation fails, you must upgrade iDRAC. See the 

Integrated 

Dell Remote Access Controller User Guide

 for more information. After you 

upgrade the iDRAC, repeat the above instructions.

Transferring an iDRAC6 Express Card

If the iDRAC6 Express card is transferred from one system to another:

• The rollback feature is unavailable on the new system. See 

Rolling Back to 

Previous BIOS and Firmware Versions

 for more information.

• All pending USC-LCE tasks that are in the process of execution are 

deleted on the new system.

• Run 

Platform Update

 wizard to download the appropriate driver pack for 

the new system.

• The driver packs, lifecycle log, and the rollback related files are deleted if 

the iDRAC6 Express card is transferred to a different Dell system. For 

example, if moving the iDRAC6 Express card from Dell PowerEdge R410 

system to Dell PowerEdge T410 system.

 

NOTE: 

Ensure that you export the lifecycle log to a different location before 

you transfer the iDRAC6 Express card.

Removing iDRAC6 Express Card

To remove the iDRAC6 express card:

1

Turn off the system, including any attached peripherals, and disconnect 

the system from the electrical outlet. To discharge the residual power in 

the system, press the power button once.

2

Remove the iDRAC6 Express card from the iDRAC6 Express slot. See the 

Hardware Owner’s Manual

 for your system for more information on 

Installing iDRAC6 Express Card. 

3

Reconnect the system and peripherals to their power sources.

4

Turn on the system, and then press 

<F10>

 to enter USC.

Summary of Contents for USC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands