Dell Studio XPS 13 - Laptop - Obsidian Service Manual Download Page 7

Page: 7 / 41

Recommended tools

The procedures in this document require the following tools:

•

Phillips screwdriver

•

Torx #5 (T5) screwdriver

•

Plastic scribe

Screw list

Table 1. Screw List

Component

Secured to

Screw type

Quantity

Base cover

Palm-rest assembly

M1.6x4

Base cover

Palm-rest assembly

M2x3

Battery

Palm-rest assembly

M1.6x4

Battery

Palm-rest assembly

M2x3

CPU plate

System board

M1.6x2.5

Display-cable bracket

System board

M1.6x2.5

Display hinges

Palm-rest assembly

M2.5x3.5

Fingerprint reader bracket

Palm-rest assembly

M1.6x1.5

Hard drive plate

System board

M1.6x2.5

Hard-drive (SSD) bracket

Palm-rest assembly

M1.6x3

Keyboard

Palm-rest assembly

M2x2

Keyboard

Palm-rest assembly

M1.6x1.5

Middle bezel

LCD cover

M1.6x3

Security-cable slot

Palm-rest assembly

M2x3

Speakers

Palm-rest assembly

M2x2

System board

Palm-rest assembly

M1.6x3

System board

Palm-rest assembly

M1.6x2.5

Touch pad

Palm rest

M2x2

Wireless card bracket

System board

M1.6x2.5

Before working inside your computer

Summary of Contents for Studio XPS 13 - Laptop - Obsidian










































Search results

Summary of Contents for Studio XPS 13 - Laptop - Obsidian

Reviews:

Related manuals for Studio XPS 13 - Laptop - Obsidian

Brands by name

Popular brands

Dell Studio XPS 13 - Laptop - Obsidian, Service Manual

Search results

Summary of Contents for Studio XPS 13 - Laptop - Obsidian

Reviews:

Related manuals for Studio XPS 13 - Laptop - Obsidian

Brands by name

Popular brands