manualshive.com logo in svg

Dell Studio 1569, Service Manual, Page: 18 / 47

Share
Download
Dell Studio 1569 Service Manual Download Page 18

  

 

 

Replacing the Display Bezel 

 

 

1.

Follow the procedures in 

Before You Begin

.  

 

 

  

2.

Ensure the display and Mini-Card cables route through the hinge portion of the display bezel, and snap the display bezel onto the display assembly.  
 

 

  

3.

Replace the four screws that secure the display bezel to the display assembly.  
 

 

  

4.

Replace the four rubber pads that cover the display bezel screws.  
 

 

  

5.

Replace the display assembly (see 

Replacing the Display Assembly

).  

 

 

  

6.

Replace the battery (see 

Replacing the Battery

).  

 

 

 

 

Display Panel  

 

 

Removing the Display Panel 

 

 

1.

Follow the procedures in 

Before You Begin

.  

 

 

  

2.

Remove the display assembly (see 

Removing the Display Assembly

).  

 

 

  

3.

Remove the display bezel (see 

Removing the Display Bezel

).  

 

 

  

4.

Remove the four screws that secure the display panel to the display cover.  
 

 

  

5.

Lift the display panel and turn it over onto a clean surface.  
 

1 

screws (4) 

2 

rubber pads (4) 

3 

display bezel 

 

 

 

 

 

CAUTION: 

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may 

result in damage to the computer.

Summary of Contents for Studio 1569
















































Reviews:

No comments