manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

Version

Description

9.7(0.0)

Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series.

ipv6 dhcp snooping vlan

Enable ipv6 DHCP Snooping on VLAN or range of VLANs.

Syntax

[no] ip dhcp snooping vlan 

vlan-id

To disable the ipv6 dhcp snooping on VLAN basis or range of VLAN, use the 

no ipv6 dhcp snooping vlan 

<vlan-id>

 command.

Parameters

vlan-id

Enter the name of a VLAN id or list of the VLANs to enable DHCP Snooping.

Defaults

Disabled

Command Modes

CONFIGURATION

Command History

This guide is platform-specific. For command information about other platforms, see the relevant 

Dell Networking 

OS Command Line Reference Guide

.

Version

Description

9.10(0.0)

Introduced on the S6100-ON.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series.

ip dhcp snooping binding

Create a static entry in the DHCP binding table.

Syntax

[no] ip dhcp snooping binding mac 

address

 vlan-id 

vlan-id

 ip 

ip-address 

interface 

interface-type

 lease 

number

Parameters

mac 

address

Enter the keyword 

mac

 then the MAC address of the host to which the server is leasing 

the IP address.

vlan-id 

vlan-id

Enter the keywords 

vlan-id

 then the VLAN to which the host belongs. The range is 

from 2 to 4094.

ip 

ip-address

Enter the keyword 

ip

 then the IP address that the server is leasing.

interface 

type

Enter the keyword 

interface

 then the type of interface to which the host is 

connected:

Dynamic Host Configuration Protocol (DHCP)

563

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

D-Link DUB-1340 Datasheet preview
DUB-1340
Brand: D-Link Pages: 2
D-Link DKVM-4U Specifications preview
DKVM-4U
Brand: D-Link Pages: 2
D-Link DKVM-16 - KVM Switch Manual preview
DKVM-16 - KVM Switch
Brand: D-Link Pages: 24
D-Link Dis-200G Series Web Ui Reference Manual preview
Dis-200G Series
Brand: D-Link Pages: 161
D-Link Dis-200G Series Quick Installation Manual preview
Dis-200G Series
Brand: D-Link Pages: 16
D-Link Dis-200G Series Hw Installation Manual preview
Dis-200G Series
Brand: D-Link Pages: 47
D-Link DGS-3130-30PS Quick Installation Manual preview
DGS-3130-30PS
Brand: D-Link Pages: 25
D-Link DGS-3100 SERIES Hardware Installation Manual preview
DGS-3100 SERIES
Brand: D-Link Pages: 54
D-Link DGS-3100 SERIES Cli Manual preview
DGS-3100 SERIES
Brand: D-Link Pages: 220
D-Link DGS-3000-28SC Quick Installation Manual preview
DGS-3000-28SC
Brand: D-Link Pages: 24
D-Link DGS-1248T - Switch Manual preview
DGS-1248T - Switch
Brand: D-Link Pages: 52
D-Link DGS-1216T - Switch Getting Started Manual preview
DGS-1216T - Switch
Brand: D-Link Pages: 42
D-Link DGS-1216T - Switch Quick Installation Guid preview
DGS-1216T - Switch
Brand: D-Link Pages: 10
D-Link DGS-1010MP Installation Manual preview
DGS-1010MP
Brand: D-Link Pages: 8
D-Link DES-3350SR Command Line Interface Reference Manual preview
DES-3350SR
Brand: D-Link Pages: 379
D-Link DES-3326SR Manual preview
DES-3326SR
Brand: D-Link Pages: 240
D-Link DES-3350SR User Manual preview
DES-3350SR
Brand: D-Link Pages: 188
D-Link DES-3326S - Switch - Stackable User Manual preview
DES-3326S - Switch - Stackable
Brand: D-Link Pages: 349

Brands by name

Popular brands

Load more brands