manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

Version

Description

8.3.12.0

Introduced on the S4810.

8.3.11.1

Introduced on the Z9000.

8.4.1.0

Introduced on the C-Series and S-Series.

dot1x auth-fail-vlan

Configure an authentication failure VLAN for users and devices that fail 802.1X authentication.

Syntax

dot1x auth-fail-vlan 

vlan-id

 [max-attempts 

number

]

To delete the authentication failure VLAN, use the 

no dot1x auth-fail-vlan 

vlan-id

 [max-

attempts 

number

]

 command.

Parameters

vlan-id

Enter the VLAN Identifier. The range is from 1 to 4094.

max-attempts 

number

(OPTIONAL) Enter the keywords 

max-attempts

 followed number of attempts desired 

before authentication fails. The range is from 1 to 5. The default is 

3

.

Defaults

3

 attempts

Command Modes

CONFIGURATION (

conf-if-interface-slot/port

)

Command History

This guide is platform-specific. For command information about other platforms, see the relevant 

Dell Networking 

OS Command Line Reference Guide

.

Version

Description

9.10(0.0)

Introduced on the S6100-ON.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced on the S6000–ON.

9.2(1.0)

Introduced on the Z9500.

9.0.2.0

Introduced on the S6000.

9.0.0.0

Introduced on the Z9000.

8.3.19.0

Introduced on the S4820T.

8.3.12.0

Introduced on the S4810.

8.3.11.1

Introduced on the Z9000.

8.4.1.0

Introduced on the C-Series and S-Series.

Usage Information

If the host responds to 802.1X with an incorrect login/password, the login fails. The switch attempts to 
authenticate again until the maximum attempts configured is reached. If the authentication fails after all allowed 
attempts, the interface moves to the authentication failed VLAN.

156

802.1X

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

Eaton NR Installation And Operation Instructions Manual preview
NR
Brand: Eaton Pages: 12
Canoga Perkins HS8000 Quick Start Manual preview
HS8000
Brand: Canoga Perkins Pages: 7
GarrettCom PS14H-48VDC Installation And User Manual preview
PS14H-48VDC
Brand: GarrettCom Pages: 77
Velleman VAS4 User Manual preview
VAS4
Brand: Velleman Pages: 8
National Instruments SwitchBlock Getting Started Manual preview
SwitchBlock
Brand: National Instruments Pages: 12
Comm-Tec MTX0804RA User Manual preview
MTX0804RA
Brand: Comm-Tec Pages: 10
BZB Gear BG-UHD44MA User Manual preview
BG-UHD44MA
Brand: BZB Gear Pages: 27
Boca BOCAHUB-16 Plus BEN220 Installation Manual preview
BOCAHUB-16 Plus BEN220
Brand: Boca Pages: 56
Primewire 302523/20191008SZ114 User Manual preview
302523/20191008SZ114
Brand: Primewire Pages: 12
Hama 00 012190 Operating Instructions Manual preview
00 012190
Brand: Hama Pages: 36
Zamel RWS-311D/Z Manual preview
RWS-311D/Z
Brand: Zamel Pages: 4
Black Box KVS4-1002D User Manual preview
KVS4-1002D
Brand: Black Box Pages: 15
lifeSMART BLEND Smart LS055 Quick Start Manual preview
BLEND Smart LS055
Brand: lifeSMART Pages: 13
Raritan MasterConsole II MCC16 User Manual preview
MasterConsole II MCC16
Brand: Raritan Pages: 49
PS Automation PSL 4 Installation Instructions preview
PSL 4
Brand: PS Automation Pages: 4
H3C S9820 Series Troubleshooting Manual preview
S9820 Series
Brand: H3C Pages: 53
Infra Power IPM-04 User Manual preview
IPM-04
Brand: Infra Power Pages: 80
Asus GIGAX 1116 Quick Installation Manual preview
GIGAX 1116
Brand: Asus Pages: 12

Brands by name

Popular brands

Load more brands