Dell S6100 Configuration Manual Download Page 1335

Page: 1335 / 1743

Version

Description

7.8.1.0

Introduced on the S-Series.

7.6.1.0

Introduced on the C-Series.

pre- 6.2.1.1

Introduced on the E-Series.

Usage Information

This command is intended for low-speed interfaces.

passive-interface

Suppress routing updates on a specified interface.

Syntax

passive-interface

interface

To delete a passive interface, use the

no passive-interface

interface

command.

Parameters

interface

Enter the following information:

•

For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then

the stack/slot/port/subport information.

•

For a 25-Gigabit Ethernet interface, enter the keyword

twentyFiveGigE

then the

stack/slot/port/subport information.

•

For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the stack/

slot/port[/subport] information.

•

For a 50-Gigabit Ethernet interface, enter the keyword

fiftyGigE

then the stack/

slot/port/subport information.

•

For a 100-Gigabit Ethernet interface, enter the keyword

hundredGigE

then the

stack/slot/port information.

•

For a Port Channel interface, enter the keywords

port-channel

then a number.

•

For a VLAN, enter the keyword

vlan

then a number from 1 to 4094.

Defaults

Not configured.

Command Modes

ROUTER RIP

Command History

This guide is platform-specific. For command information about other platforms, see the relevant

Dell Networking

OS Command Line Reference Guide

Version

Description

9.10(0.0)

Introduced on the S6100-ON.

9.8(1.0)

Introduced on the Z9100-ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced on the S6000-ON.

9.2(1.0)

Introduced on the Z9500.

Routing Information Protocol (RIP)

1335

«
...
1333
1334
1335
1336
1337
...
»

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for S6100

Reviews:

Related manuals for S6100

Brands by name

Popular brands

Dell S6100, Configuration Manual

Search results

Summary of Contents for S6100

Reviews:

Related manuals for S6100

Brands by name

Popular brands