manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

ip split-horizon

Enable split-horizon for RIP data on the interface. As described in RFC 2453, the split-horizon scheme prevents any routes learned over a 
specific interface to be sent back out that interface.

Syntax

ip split-horizon

To disable split-horizon, use the 

no ip split-horizon

 command.

Defaults

Enabled

Command Modes

INTERFACE

Command History

This guide is platform-specific. For command information about other platforms, see the relevant 

Dell Networking 

OS Command Line Reference Guide

.

Version

Description

9.10(0.0)

Introduced on the S6100-ON.

9.8(1.0)

Introduced on the Z9100-ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced on the S6000-ON.

9.2(1.0)

Introduced on the Z9500.

9.0.2.0

Introduced on the S6000.

8.3.19.0

Introduced on the S4820T.

8.3.11.1

Introduced on the Z9000.

8.3.7.0

Introduced on the S4810.

7.8.1.0

Introduced on the S-Series.

7.6.1.0

Introduced on the C-Series.

pre- 6.2.1.1

Introduced on the E-Series.

Related Commands

•

ip poison-reverse

 — sets the prefix for RIP routing updates.

Routing Information Protocol (RIP)

1329

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

La Toulousaine 1400 Installation Manual preview
1400
Brand: La Toulousaine Pages: 6
Balluff BNI IOL-314-S52-P012 Assembly Instructions Manual preview
BNI IOL-314-S52-P012
Brand: Balluff Pages: 22
Cablematic HUB-1230i User Manual preview
HUB-1230i
Brand: Cablematic Pages: 8
IOGear MicroHub GUH274W3 (Portuguese) Manual Do Usuário preview
MicroHub GUH274W3
Brand: IOGear Pages: 1
J-Tech Digital JTECH-HD4X48 User Manual preview
JTECH-HD4X48
Brand: J-Tech Digital Pages: 28
Generac Power Systems 004635-3 Owner'S Manual preview
004635-3
Brand: Generac Power Systems Pages: 20
Fairchild FPS FSDH0265RN Manual preview
FPS FSDH0265RN
Brand: Fairchild Pages: 20
cable matters 201063 User Manual preview
201063
Brand: cable matters Pages: 12
Cypress CLUX-C61C Operation Manual preview
CLUX-C61C
Brand: Cypress Pages: 16
TRENDnet TEG-S41SX Specifications preview
TEG-S41SX
Brand: TRENDnet Pages: 2
DSPPA MAG-808 User Manual preview
MAG-808
Brand: DSPPA Pages: 31
Cabletron Systems Spectrum 2E42-27 Management Manual preview
Spectrum 2E42-27
Brand: Cabletron Systems Pages: 77
B&B Electronics Elinx EIRP305-T Quick Start Manual preview
Elinx EIRP305-T
Brand: B&B Electronics Pages: 2
Ross ACO-2200 User Manual preview
ACO-2200
Brand: Ross Pages: 42
CYP EL-5500 Operation Manual preview
EL-5500
Brand: CYP Pages: 28
Kramer VS-3232DN User Manual preview
VS-3232DN
Brand: Kramer Pages: 149
Lantech LPES-2224C User Manual preview
LPES-2224C
Brand: Lantech Pages: 108
Abus FUBE50061 Installation Instructions And User Manual preview
FUBE50061
Brand: Abus Pages: 188

Brands by name

Popular brands

Load more brands