– For a VLAN interface, enter the keyword
vlan
then a number from 1 to 4094.
Example of the
show ipv6 interface
Command
Dell#show ipv6 int ManagementEthernet 1/1
ManagementEthernet 1/1 is up, line protocol is up
IPV6 is enabled
Stateless address autoconfiguration is enabled
Link Local address: fe80::201:e8ff:fe8b:386e
Global Unicast address(es):
Actual address is 400::201:e8ff:fe8b:386e, subnet is 400::/64
Actual address is 412::201:e8ff:fe8b:386e, subnet is 412::/64
Virtual-IP IPv6 address is not set
Received Prefix(es):
400::/64 onlink autoconfig
Valid lifetime: 2592000, Preferred lifetime: 604800
Advertised by: fe80::201:e8ff:fe8b:3166
412::/64 onlink autoconfig
Valid lifetime: 2592000, Preferred lifetime: 604800
Advertised by: fe80::201:e8ff:fe8b:3166
Global Anycast address(es):
Joined Group address(es):
ff02::1
ff02::1:ff8b:386e
ND MTU is 0
ICMP redirects are not sent
DAD is enabled, number of DAD attempts: 3
ND reachable time is 32000 milliseconds
ND base reachable time is 30000 milliseconds
ND retransmit interval is 1000 milliseconds
ND hop limit is 64
Showing IPv6 Routes
To view the global IPv6 routing information, use the following command.
• Show IPv6 routing information for the specified route type.
EXEC mode
show ipv6 route [vrf vrf-name]
type
The following keywords are available:
– To display information about a network, enter
ipv6 address
(X:X:X:X::X).
– To display information about a host, enter
hostname
.
– To display information about all IPv6 routes (including non-active routes), enter
all
.
– To display information about all connected IPv6 routes, enter
connected
.
– To display information about brief summary of all IPv6 routes, enter
summary
.
– To display information about Border Gateway Protocol (BGP) routes, enter
bgp
.
– To display information about ISO IS-IS routes, enter
isis
.
– To display information about Open Shortest Path First (OSPF) routes, enter
ospf
.
– To display information about Routing Information Protocol (RIP), enter
rip
.
– To display information about static IPv6 routes, enter
static
.
516
IPv6 Routing
Summary of Contents for S4820T
