manualshive.com logo in svg

Dell S3840cdn, User Manual

Share
Download
Dell S3840cdn User Manual Download Page 69

USB

|

69

USB

This section describes the features you can select on the 

Print from USB

 screen.

NOTE:

•

To prevent damage to your printer, do not connect any device other than USB memory to the front 
USB port of the printer.

•

Do not remove the USB memory from the front USB port until the printer has finished printing.

•

When the Authentication or Accounting feature is enabled, a user ID and passcode may be required. 
Ask your system administrator for the user ID and passcode.

•

Data stored in USB memory device may be lost or damaged in the following cases. Make sure to 
back up data in media before use.

- When disconnecting/connecting the USB memory device by methods other than those 

described in this guide

- When receiving the effect of electrical noise or an electrical discharge
- When a fault or failure occurs during operation
- If the USB memory device receives mechanical damage

•

We assume no responsibility for any direct and indirect damages arising from or caused by such 
data loss.

Supported USB

For the front USB port of the printer, you can use a USB flash drive with the following 
specification:

•

USB 2.0 memory device

•

USB memory devices with the capacity of up to 256 GB.

•

USB memory devices that support FAT12, FAT16, FAT32, and VFAT (long name).

NOTE:

•

If the USB flash drive is formatted in a file system other than the above, the printer may not detect 
the USB flash drive.

•

A USB flash drive with authentication feature and some brands of USB flash drive cannot be used 
with this printer.

Summary of Contents for S3840cdn































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands