manualshive.com logo in svg

Dell PowerVault MD3260i Series, Deployment Manual

The Dell PowerVault MD3260i Series Troubleshooting Manual is a comprehensive guide designed to assist users in resolving any issues they may encounter with their MD3260i storage system. This essential manual is available for free download from our website, ensuring easy access for users seeking assistance with their Dell PowerVault MD3260i Series.

Share
Download
background image

4.

Edit the following entries in the /etc/iscsi/iscsid.conf file:
a) Edit or verify that the

 node.startup = manual

 line is disabled.

b) Edit or verify that the 

node.startup = automatic 

line is enabled.

This enables automatic startup of the service at boot time.

c) Verify that the following time-out value is set to 30 by running the following command:

 node.session.timeo.replacement_timeout = 30 

d) Save and close the /etc/iscsi/iscsid.conf file.

5.

From the console, restart the iSCSI service with the following command:

service iscsi start

6.

Verify that the iSCSI service is running during boot using the following command from the console:

chkconfig iscsi on

7.

To display the available iSCSI targets at the specified IP address, use the following command:

iscsiadm –m discovery –t st -p <IP_address_of_iSCSI_port>

8.

After target discovery, use the following command to manually log in:

iscsiadm -m node –l 

This log in is performed automatically at startup if automatic startup is enabled.

9.

Manually log out of the session using the following command:

iscsiadm -m node -T <initiator_username> -p  <target_ip> -u

Step 4: Configure Host Access

This step specifies which host servers access virtual disks on the storage array. You should perform this step:

•

Before mapping virtual disks to host servers

•

Any time you connect new host servers to the storage array

1.

Launch MD Storage Manager.

2.

Navigate to the AMW and click Manually define hosts.

3.

At Enter host name, enter the host server for virtual disk mapping.
This can be an informal name, not necessarily a name used to identify the host server to the network.

4.

Select a method for adding the host port identifier

5.

Select the host type.

6.

Select whether or not the host server will be part of a host server group that shares access to the same virtual 

disks as other host servers. Select Yes only if the host is part of a Microsoft cluster.

7.

Click Next.

8.

Specify if this host will be part of a host group.

9.

Click Finish.

Understanding CHAP Authentication

What Is CHAP

Challenge Handshake Authentication Protocol (CHAP) is an optional iSCSI authentication method where the storage 
array (target) authenticates iSCSI initiators on the host server. Two types of CHAP are supported:

•

Target CHAP

•

Mutual CHAP

37

Summary of Contents for PowerVault MD3260i Series


























































Reviews:

No comments

Related manuals for PowerVault MD3260i Series

Baaske Medical Docpad 10c W User Manual preview
Docpad 10c W
Brand: Baaske Medical Pages: 40
Supermicro Desktop 5130DQ-IL User Manual preview
Desktop 5130DQ-IL
Brand: Supermicro Pages: 107
DFI WM342-KD Series Installation Manual preview
WM342-KD Series
Brand: DFI Pages: 12
Wyse WY-60 User Manual preview
WY-60
Brand: Wyse Pages: 114
Lanoptik MV60 User Manual preview
MV60
Brand: Lanoptik Pages: 16
Dell Precision R5400 User Manual preview
Precision R5400
Brand: Dell Pages: 111
BESTEK MEB-7601 Quick Manual preview
MEB-7601
Brand: BESTEK Pages: 11
Electronic M101H Operating Instructions preview
M101H
Brand: Electronic Pages: 4
Power Computing Minitower 132 User Manual preview
Minitower 132
Brand: Power Computing Pages: 31
Fujitsu Siemens Computers SCENIC eT Operating Manual preview
SCENIC eT
Brand: Fujitsu Siemens Computers Pages: 54
Fujitsu Siemens Computers AMILO Desktop S Series First-Time Setup preview
AMILO Desktop S Series
Brand: Fujitsu Siemens Computers Pages: 141
Nexcom NISE 505 User Manual preview
NISE 505
Brand: Nexcom Pages: 74
IEI Technology tKINO-ULT3 User Manual preview
tKINO-ULT3
Brand: IEI Technology Pages: 151
IEI Technology NANO-BT-i1 Series User Manual preview
NANO-BT-i1 Series
Brand: IEI Technology Pages: 153
Mitsubishi Apricot MS Series Owner'S Handbook Manual preview
Apricot MS Series
Brand: Mitsubishi Pages: 87
S&T Kontron SBOX-7210 User Manual preview
Kontron SBOX-7210
Brand: S&T Pages: 99
Stanley 07535 Instruction Manual preview
07535
Brand: Stanley Pages: 452
Swedstyle Space Operating Manual preview
Space
Brand: Swedstyle Pages: 8

Brands by name

Popular brands

Load more brands