manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Figure 59. Installing the 1.8 inch SSD cage

1.

1.8 inch SSD backplane connector

2. 1.8 inch SSD backplane

3. 1.8 inch SSD cage

4. tab on the SSD cage

5. tab on the PSU 1 slot (2)

6. slot on the chassis

Next steps

1.

Install the 1.8 inch SSD carrier or SSD blank(s) into the SSD cage.

2.

Follow the procedure listed in after working inside your system.

Related Links

Safety instructions
Installing a 1.8 inch uSATA SSD blank
Installing a 1.8 inch uSATA SSD carrier
Removing the 1.8 inch uSATA SSD cage

Removing the 1.8 inch uSATA SSD backplane

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only 
perform troubleshooting and simple repairs as authorized in your product documentation, or as 
directed by the online or telephone service and support team. Damage due to servicing that is 
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions 
that are shipped with your product.

1.

Follow the safety guidelines listed in the Safety instructions section.

2.

Follow the procedure listed in before working inside your system.

136

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

Aastra AXD Installation And Maintenance Manual preview
AXD
Brand: Aastra Pages: 502
IBM x3655 - System - 7985 User Manual preview
x3655 - System - 7985
Brand: IBM Pages: 118
Patton electronics 29XX Series Administrator'S Reference Manual preview
29XX Series
Brand: Patton electronics Pages: 326
IBM eServer BladeCenter HS40 Type 8839 Installation And User Manual preview
eServer BladeCenter HS40 Type 8839
Brand: IBM Pages: 120
Velvac Road-iQ Installation Manual preview
Road-iQ
Brand: Velvac Pages: 55
Sollae Systems EZL-200 User Manual preview
EZL-200
Brand: Sollae Systems Pages: 27
Supero SUPERSERVER 5015M-MF User Manual preview
SUPERSERVER 5015M-MF
Brand: Supero Pages: 120
MAXDATA PLATINUM 1500 IR M5 User Manual preview
PLATINUM 1500 IR M5
Brand: MAXDATA Pages: 44
IBM x3105 - System - 4347 Service Manual preview
x3105 - System - 4347
Brand: IBM Pages: 130
IBM System x3650 Type 7979 Problem Determination And Service Manual preview
System x3650 Type 7979
Brand: IBM Pages: 194
Leightronix UltraNEXUS User Manual preview
UltraNEXUS
Brand: Leightronix Pages: 22
Planet FPS-1100DG User Manual preview
FPS-1100DG
Brand: Planet Pages: 72
Cooper Bussmann BU-945U-E User Manual preview
BU-945U-E
Brand: Cooper Bussmann Pages: 82
3Com OfficeConnect 3C19500 Installation Manual preview
OfficeConnect 3C19500
Brand: 3Com Pages: 1
IBM 4252E1U Datasheet preview
4252E1U
Brand: IBM Pages: 2
VVDN Technologies DT4CS User'S Manual Manual preview
DT4CS
Brand: VVDN Technologies Pages: 35
GIGA-BYTE TECHNOLOGY G262-ZR0 User Manual preview
G262-ZR0
Brand: GIGA-BYTE TECHNOLOGY Pages: 137
Lantronix WiBox2100E User Manual preview
WiBox2100E
Brand: Lantronix Pages: 94

Brands by name

Popular brands

Load more brands