manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Removing an AC power supply unit

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only 
perform troubleshooting and simple repairs as authorized in your product documentation, or as 
directed by the online or telephone service and support team. Damage due to servicing that is 
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions 

that are shipped with your product.

CAUTION: The system requires one power supply unit (PSU) for normal operation. On power-
redundant systems, remove and install only one PSU at a time in a system that is powered on.

1.

Follow the safety guidelines listed in the safety instructions section.

2.

Disconnect the power cable from the power source and from the PSU you intend to remove.

3.

Remove the cables from the strap on the PSU.

Steps

Press the release latch and slide the PSU out of the PSU slot by holding the PSU handle.

Figure 40. Removing an AC PSU

1.

release latch

2. PSU cable connector

3. PSU

4. connector

5. PSU handle

Next steps

Depending on your requirement, perform one of the following steps:

• If you are not replacing PSU 2 immediately, install a PSU blank.
• Install the replacement AC PSU.
• Install the 2.5 inch hard drive cage.

Related Links

Safety instructions
Installing an AC power supply unit
Installing the power supply unit blank

115

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

SMC Sierra Monitor FS-8704-14 Driver Manual preview
FS-8704-14
Brand: SMC Sierra Monitor Pages: 42
Supero SUPERSERVER 6027R-TRF User Manual preview
SUPERSERVER 6027R-TRF
Brand: Supero Pages: 102
i3 International SRX-Pro Server Quick Start Manual preview
SRX-Pro Server
Brand: i3 International Pages: 2
Supermicro SuperWorkstation 740A-T User Manual preview
SuperWorkstation 740A-T
Brand: Supermicro Pages: 138
Cyclades Cyclades-PR4000 Installation Manual preview
Cyclades-PR4000
Brand: Cyclades Pages: 174
Pathos Acoustics Musiteca Operating Instructions Manual preview
Musiteca
Brand: Pathos Acoustics Pages: 26
Buffalo BS-GS2008P Quick Setup Manual preview
BS-GS2008P
Brand: Buffalo Pages: 2
ANTAIRA STW-611C Installation Manual preview
STW-611C
Brand: ANTAIRA Pages: 2
Intermec Norand 6920 Reference Manual preview
Norand 6920
Brand: Intermec Pages: 232
IBM 8672-26x Manual preview
8672-26x
Brand: IBM Pages: 75
Inspur NF5486M5 Installation Manual preview
NF5486M5
Brand: Inspur Pages: 2
Infotrend EonServ 7000 Series Quick Installation Manual preview
EonServ 7000 Series
Brand: Infotrend Pages: 2
DataOn Storage CiB-9224 V12 Technical Manual preview
CiB-9224 V12
Brand: DataOn Storage Pages: 36
Philips System4 Seriver Installation Instructions Manual preview
System4 Seriver
Brand: Philips Pages: 48
Supermicro SUPERSERVER 5028TK-HTR User Manual preview
SUPERSERVER 5028TK-HTR
Brand: Supermicro Pages: 138
Inventec P47 series Service Manual preview
P47 series
Brand: Inventec Pages: 129
2Wire MEMO2 WS.502 Manual preview
MEMO2 WS.502
Brand: 2Wire Pages: 35
Black Box LWS405A Quick Start Manual preview
LWS405A
Brand: Black Box Pages: 1

Brands by name

Popular brands

Load more brands