Dell PowerEdge C4130 Owner'S Manual Download Page 113 | Manualshive

Page: 113 / 217

background image

Removing the power supply unit blank

Remove the power supply unit (PSU) blank when you are installing a second PSU or a 2.5 inch hard drive
cage in the PSU 2 slot.

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that are shipped with your product.

Follow the safety guidelines listed in the Safety instructions section.

Steps

Remove the PSU blank from the PSU 2 slot by pulling the blank outward.

CAUTION: To ensure proper system cooling, the PSU blank must be installed in the PSU 2 slot
in a non-redundant configuration. Remove the PSU blank only if you are installing a second
PSU or a 2.5 inch hard drive cage.

Figure 38. Removing the PSU blank

1.

PSU blank

2. PSU bay

Next steps

Install PSU 2 or the 2.5 inch hard drive cage.

Related Links

Safety instructions
Installing an AC power supply unit
Installing the optional 2.5 inch hard drive cage
Installing the power supply unit blank

113

«
...
111
112
113
114
115
...
»

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

Brand: Unisys Pages: 20

Brand: Xerox Pages: 2

eserver xSeries 440

Brand: IBM Pages: 34

Brand: Altos Pages: 93

Brand: Fibrenetix Pages: 17

System x3500 M2 Type 7839

Brand: IBM Pages: 126

8668 - Eserver xSeries 232

Brand: IBM Pages: 182

BullSequana Edge nano

Brand: Atos Pages: 29

TERASTATION HS-D1.0TGL/R5

Brand: Buffalo Pages: 2

Brand: Zeiss Pages: 12

Brand: Docomo Pages: 61

Brand: GRASS VALLEY Pages: 2

Brand: SAFARI Montage Pages: 8

Brand: SAFARI Montage Pages: 8

NETWORK PROXY SERVER 4.0 -

Brand: Red Hat Pages: 44

NETWORK PROXY 5.3.0 -

Brand: Red Hat Pages: 48

Brand: Allnet Pages: 12

Com Port Redirector

Brand: Lantronix Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands