Dell PowerEdge 700 Installation And Troubleshooting Manual Download Page 54

Page: 54 / 94

If the problem persists, see "

Getting Help

Troubleshooting a SATA Hard Drive in a RAID Configuration (When Available)

Problem

Device driver error.

Damaged or improperly connected hard-drive cables.

Action

Run the appropriate online diagnostic test. See "

Using Server Administrator Diagnostics

" in "Running System Diagnostics."

If the test fails, continue to the next step.

Restart your system and enter the RAID configuration utility. See the RAID controller card's documentation.

Ensure that the required device drivers are installed and are configured correctly. See the

Dell OpenManage Server Assistant

CD and the RAID controller

card's documentation.

Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

Remove the bezel. See "

Removing the Bezel

Lay the system on its right side.

Remove the cover. See "

Removing the Cover

Ensure that the hard-drive interface cable is properly connected to the drive and to the controller card. See the card's documentation.

Ensure that the RAID controller card is installed correctly. See "

Expansion Cards

" in "Installing System Options."

10.

If the hard drive is the boot drive, ensure that the drive is configured and connected properly. See "

Configuring the Boot Drive

" in "Installing Drives."

11.

Ensure that the power cable is properly connected to the drive.

12.

Replace the cover. See "

Replacing the Cover

13.

Stand the system upright.

14.

Install the bezel. See "

Installing the Bezel

15.

Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

16.

Format and partition the hard drive. See the operating system documentation.

17.

If possible, restore the files to the drive.

If the problem persists, see "

Getting Help

Troubleshooting Expansion Cards

Problem

Error message indicates a problem with an expansion card.

Expansion card performs incorrectly or not at all.

Action

CAUTION:

See your

System Information Guide

for complete information about safety precautions, working inside the computer, and protecting

against electrostatic discharge.

NOTICE:

This troubleshooting procedure can destroy data stored on the hard drive. Before you proceed, back up all files on the hard drive.

NOTE:

When troubleshooting an expansion card, see the documentation for your operating system and the expansion card.

Summary of Contents for PowerEdge 700































































































Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands

Dell PowerEdge 700, Installation And Troubleshooting Manual

Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands