manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 239

e em contacto com a ligação à terra, podendo causar queimaduras graves
ou ficarem soldados aos terminais.

WARNING:

¡Atención!

Antes de operar sobre equipos conectados a líneas

de alimentación, quitarse las joyas (incluidos anillos, collares y relojes). Los
objetos de metal se calientan cuando se conectan a la alimentación y a tierra,
lo que puede ocasionar quemaduras graves o que los objetos metálicos
queden soldados a los bornes.

WARNING:

Varning!

Tag av alla smycken (inklusive ringar, halsband och

armbandsur) innan du arbetar på utrustning som är kopplad till kraftledningar.
Metallobjekt hettas upp när de kopplas ihop med ström och jord och kan
förorsaka allvarliga brännskador; metallobjekt kan också sammansvetsas
med kontakterna.

Lightning Activity Warning

WARNING:

Do not work on the system or connect or disconnect cables during

periods of lightning activity.

WARNING:

Waarschuwing

Tijdens onweer dat gepaard gaat met bliksem,

dient u niet aan het systeem te werken of kabels aan te sluiten of te
ontkoppelen.

WARNING:

Varoitus

Älä työskentele järjestelmän parissa äläkä yhdistä tai

irrota kaapeleita ukkosilmalla.

WARNING:

Attention

Ne pas travailler sur le système ni brancher ou

débrancher les câbles pendant un orage.

WARNING:

Warnung

Arbeiten Sie nicht am System und schließen Sie keine

Kabel an bzw. trennen Sie keine ab, wenn es gewittert.

WARNING:

Avvertenza

Non lavorare sul sistema o collegare oppure scollegare

i cavi durante un temporale con fulmini.

223

Chapter 18: Installation and Maintenance Safety Information

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands