manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 134

NOTE:

Both fan trays must be installed in the chassis for normal switch

operation.

Related

Documentation

Removing a Fan Tray from a J-EX8216 Switch on page 159

•

•

Cooling System and Airflow in a J-EX8216 Switch on page 44

Installing an RE Module in a J-EX8216 Switch

You can install either one or two Routing Engine (RE) modules in a J-EX8216 switch. The
RE modules install horizontally in the front of the chassis in the slots labeled RE0 and
RE1. See “Slot Numbering for a J-EX8216 Switch” on page 14.

NOTE:

We recommend that you install two RE modules for redundancy. If

you install only one RE module, we recommend that you install it in the slot
RE0.

CAUTION:

Do not lift the RE module by holding the ejector levers. The levers

cannot support the weight of the module. Lifting the modules by the levers
might bend the levers, and the bent levers will prevent the RE module from
being properly seated in the chassis.

Before you begin installing an RE module in a J-EX8216 switch:

•

Ensure you understand how to prevent ESD damage. See “Prevention of Electrostatic
Discharge Damage on J-EX Series Switches” on page 230.

Ensure that you have the following parts and tools available to install an RE module:

•

Electrostatic discharge (ESD) grounding strap

•

Phillips (+) screwdriver, number 2

To install an RE module in a J-EX8216 switch (see Figure 50 on page 119):

1.

Attach the electrostatic discharge (ESD) grounding strap to your bare wrist and
connect the strap to one of the ESD points on the chassis.

2.

Taking care not to touch the leads, pins, or solder connections, pull the RE module
out from the bag.

3.

Pull both the ejector levers outward, away from the faceplate of the RE module, until
they go no further.

4.

If the slot has a cover panel on it, unscrew the two screws on either side of the cover
panel counterclockwise using the Phillips (+) screwdriver, number 2. Remove the
cover panel. Save the cover panel for later use.

118

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands