Dell P80G Service Manual Download Page 122 | Manualshive

Page: 122 / 131

background image

Steps

1. Locate the display panel on the display back cover assembly.
2. Remove the four (M2.5x3.5) screws that secure the display panel to the display assembly.
3. Lift to turn over the display panel to access the display cable.
4. Peel the conductive tape on the display cable connector.
5. Lift the latch and disconnect the display cable from the connector on the display panel.

NOTE:

Do not pull and release the Stretch (SR) Tapes from the display panel. There is no need to separate the

brackets from the display panel.

Installing the display panel

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the display panel and provides a visual representation of the installation procedure.

122

Disassembly and reassembly

«
...
120
121
122
123
124
...
»

Summary of Contents for P80G




































































































































Reviews:

No comments

Related manuals for P80G

Veriton Hornet N260G

Brand: Acer Pages: 22

Brand: Radio Shack Pages: 31

Brand: Radio Shack Pages: 30

Brand: Radio Shack Pages: 42

Brand: Radio Shack Pages: 192

Brand: Radio Shack Pages: 274

Brand: Radio Shack Pages: 44

Brand: Radio Shack Pages: 30

Brand: EBN Pages: 9

Decision Mate V

Brand: NCR Pages: 426

Brand: Gateway Pages: 126

Brand: EUROCOM Pages: 113

NUC 11 Performance

Brand: Intel Pages: 20

FlowControl FC-S01

Brand: Go!Paint Pages: 20

Brand: Omnitronic Pages: 56

Brand: Acer Pages: 48

Brand: Acer Pages: 68

5535-5050 - Aspire

Brand: Acer Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands