Dell P80G Service Manual Download Page 105 | Manualshive

Page: 105 / 131

background image

Steps

1. Locate the display cable, touchscreen cable and display hinges on your computer.
2. Peel back the tape and disconnect the touchscreen cable.
3. Remove the two (M2x3) screws that secure the EDP metal bracket to the computer.
4. Peel the tape that secures the display cable to the system board.
5. Open the latch and disconnect the display cable from the system board.
6. Unroute the WLAN and WWAN cables from the retention clips.
7. Remove the six (M2.5x4) screws that secure the display hinges to the chassis of your computer.
8. Open the display hinges at an angle of 90 degrees and slightly open the display.
9. Remove the palm-rest and keyboard assembly off the display assembly.

Installing the display assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the component and provides a visual representation of the installation procedure.

Disassembly and reassembly

105

«
...
103
104
105
106
107
...
»

Summary of Contents for P80G




































































































































Reviews:

No comments

Related manuals for P80G

ECS-9671 GTX950

Brand: Vecow Pages: 111

kontron KBox B-201-CFL

Brand: S&T Pages: 72

IntelliStation 6866

Brand: IBM Pages: 148

Brand: Vivo Pages: 8

Brand: Vivo Pages: 2

Brand: Mitsubishi Electric Pages: 30

apricot ls/vs550

Brand: Mitsubishi Electric Pages: 67

Brand: Mitsubishi Electric Pages: 80

Brand: Mitsubishi Electric Pages: 26

Apricot FT S Pentium Series

Brand: Mitsubishi Electric Pages: 18

Brand: Mitsubishi Electric Pages: 26

Brand: Mitsubishi Electric Pages: 101

Brand: Mitsubishi Electric Pages: 105

Brand: Mitsubishi Electric Pages: 81

Brand: Mitsubishi Electric Pages: 102

Brand: Mitsubishi Electric Pages: 116

Brand: Mitsubishi Electric Pages: 124

Brand: Mitsubishi Electric Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands