Dell P152G Service Manual Download Page 72 | Manualshive

Page: 72 / 102

background image

About this task

The following images indicate the location of the camera module (in a system shipped with an aluminum chassis) and provide a
visual representation of the removal procedure.

Steps

1. Using a plastic scribe, pry the camera module from the display back cover and flip it.

NOTE:

Start prying the camera module in a sequential order 1>2 as indicated on the display back cover.

2. Peel and unwrap the tape securing the camera module to the display back cover.
3. Disconnect the camera cable from its connector.
4. Lift the camera module.

Installing the camera module (Aluminum)

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following images indicate the location of the camera module (in a system shipped with an aluminum chassis) and provide a
visual representation of the installation procedure.

72

Removing and installing components

«
...
70
71
72
73
74
...
»

Summary of Contents for P152G







































































































Reviews:

No comments

Related manuals for P152G

The Toughbook 31

Brand: Panasonic Pages: 2

Brand: IBM Pages: 170

Brand: DIGILION Pages: 15

AcerNote Light 370

Brand: Acer Pages: 16

Brand: Acer Pages: 28

Acer TravelMate 3300 Series

Brand: Acer Pages: 75

Brand: Acer Pages: 88

AcerNote Light 370

Brand: Acer Pages: 3

Aspire 1360 Series

Brand: Acer Pages: 143

Brand: Acer Pages: 11

Brand: Acer Pages: 79

AS7315-302G25Mn

Brand: Acer Pages: 200

AS4810T- 354G32Mn LX.PBA0X.075

Brand: Acer Pages: 148

Brand: Acer Pages: 69

Brand: Acer Pages: 224

Brand: Acer Pages: 100

Brand: Acer Pages: 92

Acer TravelMate 3300 Series

Brand: Acer Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands