manualshive.com logo in svg

Dell P152G, Service Manual, Page: 63 / 102

Share
Download
Dell P152G Service Manual Download Page 63

Steps

1. Remove the two (M2x2) screws that secure the display panel to the back cover.
2. Use a plastic scribe to pry the display panel from the bottom-right corner.
3. Gently start prying the display panel along the left and right sides of the display back-cover using your hands.
4. Lift the bottom side of the display panel and slide it downward to release the display brackets from the slots at the top side

of the display cover.

5. Gently flip the display panel assembly forward, peel back the Mylar tape securing the display cable on the rear of the display

panel.

NOTE:

 Ensure that the panel has a clean and smooth surface to rest on to prevent damage.

6. Disconnect the display cable from the display panel assembly and lift the display panel away from the system.

NOTE:

 Do not remove the metal brackets from the panel.

Installing the display panel

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following images indicate the location of the display panel and provide a visual representation of the installation procedure.

Removing and installing components

63

Summary of Contents for P152G







































































































Reviews:

No comments